HP Scitex LX600 HP Scitex LX Printer Family - Maintenance and troubleshooting - Page 40

There is a green ring on the far side of the black knob, which should not be visible if

Get HP Scitex LX600 PDF manuals and user guides View all HP Scitex LX600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

8. There is a strip of polyester film on the leading edge of the cleaning material. Insert it into the hole in the takeup core, which takes hold of it. Hardware maintenance 9. Slide the takeup core onto the lower axle. It clicks into place. NOTE: If the cleaner roll has not been properly installed, you may see a message about clearing a printhead cleaning roll jam. Pull the whole assembly out, wind a little of the roll forward, then slide it back in again. The printer will check the roll again 10. Restore the pinch system by moving the black knob back into place. If you feel resistance because the cleaning roll is too tight, turn the roll slightly counter-clockwise. TIP: There is a green ring on the far side of the black knob, which should not be visible if the knob has been correctly placed. If it is visible, try again. 11. Grip the handle and push the whole printhead cleaning roll assembly back into the printer. 12. Close the door. Do not empty the drain container: this is done by a service engineer during preventive maintenance. 34 Chapter 4 Hardware maintenance ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
8.
There is a strip of polyester film on the leading edge of the cleaning material. Insert it into the
hole in the takeup core, which takes hold of it.
9.
Slide the takeup core onto the lower axle. It clicks into place.
NOTE:
If the cleaner roll has not been properly installed, you may see a message about
clearing a printhead cleaning roll jam. Pull the whole assembly out, wind a little of the roll
forward, then slide it back in again. The printer will check the roll again
10.
Restore the pinch system by moving the black knob back into place. If you feel resistance
because the cleaning roll is too tight, turn the roll slightly counter-clockwise.
TIP:
There is a green ring on the far side of the black knob, which should not be visible if the
knob has been correctly placed. If it is visible, try again.
11.
Grip the handle and push the whole printhead cleaning roll assembly back into the printer.
12.
Close the door.
Do not empty the drain container: this is done by a service engineer during preventive maintenance.
34
Chapter 4
Hardware maintenance
ENWW
Hardware maintenance