Pioneer VSX-49TX Owner's Manual - Page 118

If the unit does not operate normally due to external effects such as static electricity

Get Pioneer VSX-49TX PDF manuals and user guides View all Pioneer VSX-49TX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 118 highlights

Techno Tidbits & Problem-solving Problem The SR cable is connected, but the connected components can't be operated with the remote. Cause settings were cleared. • The SR cable hasn't been connected properly. • The rest of the component connection have not been made. • The component you have hooked up is not SR compatible. Portions of the remote contol • The remote control may be display don't display malfunctioning. correctly. Remedy • Reinsert the SR cable, making sure it is the right jack (p.84). • Make sure an analog connection has been made between the units. • This is not a malfunction. • Reset the remote control. (Note: In doing this, all settings in the remote control will be reset to the default.) (see Resetting the Remote Control, p.92) Miscellaneous HOME THX 7.1 channel mode is selected, but there are certain options that can't be chosen. • The current setting is for only one surround back speaker. • Connect two surround back speakers (p.28) and make the settings accordingly (p.40). There seems to be a time lag • The subwoofer channel can be delayed between the speakers and slightly if run through a low-pass filter. the output of the subwoofer. • The MCACC system will automatically compensate for a delay in the subwoofer output during the Auto Surround Sound Setup. The receiver doesn't memorize the volume level last used before turn off. • Turning off the receiver immediately after • Turn off the receiver one second or more changing the volume level. after changing the volume. The receiver doesn't memorize that status of the receiver last used before turn off. • Turning off the receiver immediately after changing the receiver status. • Turn off the receiver one second or more after changing the receiver status. If the unit does not operate normally due to external effects such as static electricity Disconnect the power plug from the outlet and insert again to return to normal operating conditions. 118

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
118
Techno Tidbits & Problem-solving
•
Reinsert the SR cable, making sure it is
the right jack (p.84).
•
Make sure an analog connection has
been made between the units.
•
This is not a malfunction.
•
Reset the remote control.
(Note: In doing this, all settings in the
remote control will be reset to the default.)
(see Resetting the Remote Control, p.92)
•
Connect two surround back speakers
(p.28) and make the settings accordingly
(p.40).
•
The MCACC system will automatically
compensate for a delay in the subwoofer
output during the Auto Surround Sound
Setup.
•
Turn off the receiver one second or more
after changing the volume.
•
Turn off the receiver one second or more
after changing the receiver status.
Problem
Cause
Remedy
If the unit does not operate normally due to external effects such as static electricity
Disconnect the power plug from the outlet and insert again to return to normal operating conditions.
The SR cable is connected,
but the connected
components can't be
operated with the remote.
Portions of the remote contol
display don’t display
correctly.
Miscellaneous
HOME THX 7.1 channel mode
is selected, but there are
certain options that can't be
chosen.
There seems to be a time lag
between the speakers and
the output of the subwoofer.
The receiver doesn’t
memorize the volume level
last used before turn off.
The receiver doesn’t
memorize that status of the
receiver last used before turn
off.
settings were cleared.
•
The SR cable hasn't been connected
properly.
• The rest of the component connection
have not been made.
•
The component you have hooked up is
not SR compatible.
•
The remote control may be
malfunctioning.
•
The current setting is for only one
surround back speaker.
•
The subwoofer channel can be delayed
slightly if run through a low-pass filter.
•
Turning off the receiver immediately after
changing the volume level.
•
Turning off the receiver immediately after
changing the receiver status.