Pioneer VSX-49TX Owner's Manual - Page 60

Input Attenuator, DUAL MONO Setting and Playback, Tape 2 Monitor

Get Pioneer VSX-49TX PDF manuals and user guides View all Pioneer VSX-49TX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Basic Operation DUAL MONO Setting and Playback The dual mono setting can only be used when listening to Dolby Digital or homemade discs that have dual mono software encoded in them. Dual mono software usually is used to put two different mono recordings with one soundtrack on one DVD. With this setting you can choose which channel in the dual mono setting you want to listen to. Remember this setting is only applicable if you are using Dolby Digital software with dual mono and want to isolate one of the channels therein. Otherwise, just ignore this function. 1 Press the LISTENING CH SELECT button for more than five seconds to put the receiver in DUAL MONO mode. Hold down the LISTENING CH SELECT button to cycle 1 through the different DUAL MONO settings. When you find the one you want release the button. memo • The default setting is DUAL ch1. • You can only use this function with Dolby Digital sources that have this function. • When a DUAL MONO source is being used the Ò & Â indicators flash. Then, if you select DUAL ch1, for example, the Ò indicator will light. DUAL ch1 DUAL ch2 DUAL ch1/ch2 The different settings are: DUAL ch1, where you only hear channel 1; DUAL ch2, where you only hear channel 2; and DUAL ch1/ch2, where you hear both channels, but independently from different speakers. Input Attenuator The input attenuator lowers the input level of an analog signal when it is too strong, causing distortion in the sound. Receiver MAIN SUB TONE BASS/ TREBLE DISPLAY VIDEO DIMMER SELECT EFFECT/ CH SEL. STATUS SPEAKER A/B LOUDNESS INPUT ATT. 1 SYSTEM SETUP TAPE 2 SIGNAL MONITOR SELECT 1 Use the INPUT ATT button on the RECEIVER'S SUB screen to lower the analog input level. Tape 2 Monitor If you connect a cassette deck with a record monitor function (a three-head tape deck) to the TAPE 2 MONITOR jacks, you can listen to the sound of an analog recording as it's being recorded. 60 Receiver MAIN SUB TONE BASS/ TREBLE DISPLAY VIDEO DIMMER SELECT EFFECT/ CH SEL. STATUS SYSTEM SETUP SPEAKER A/B LOUDNESS TAPE 2 MONITOR INPUT ATT. SIGNAL SELECT 1 1 Use the TAPE 2 MONITOR button on the RECEIVER'S SUB screen to listen to the component hooked up to the TAPE 2 MONITOR jacks.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
60
Basic Operation
Input Attenuator
The input attenuator lowers the input level of an analog signal when it is too strong, causing distortion in the
sound.
1
Use the INPUT ATT button on the
RECEIVER’S SUB screen to lower the
analog input level.
STATUS
SPEAKER
A/B
LOUDNESS
INPUT
ATT.
Receiver
MAIN
SUB
SIGNAL
SELECT
TAPE 2
MONITOR
SYSTEM
SETUP
DISPLAY
DIMMER
VIDEO
SELECT
EFFECT/
CH SEL.
BASS/
TREBLE
TONE
DUAL MONO Setting and Playback
The dual mono setting can only be used when listening to Dolby Digital or homemade discs that have dual mono
software encoded in them. Dual mono software usually is used to put two different mono recordings with one
soundtrack on one DVD. With this setting you can choose which channel in the dual mono setting you want to
listen to. Remember this setting is only applicable if you are using Dolby Digital software with dual mono and
want to isolate one of the channels therein. Otherwise, just ignore this function.
1
Press the LISTENING CH SELECT
button for more than five seconds to
put the receiver in DUAL MONO
mode.
Hold down the LISTENING CH SELECT button to cycle
through the different DUAL MONO settings.
When you
find the one you want release the button.
DUAL ch2
DUAL ch1
DUAL ch1/ch2
The different settings are: DUAL ch1, where you only
hear channel 1; DUAL ch2, where you only hear channel
2; and DUAL ch1/ch2, where you hear both channels,
but independently from different speakers.
memo
1
Tape 2 Monitor
If you connect a cassette deck with a record monitor function (a three-head tape deck) to the TAPE 2
MONITOR jacks, you can listen to the sound of an analog recording as it
’
s being recorded.
1
Use the TAPE 2 MONITOR button on
the RECEIVER’S SUB screen to listen
to the component hooked up to the
TAPE 2 MONITOR jacks.
STATUS
SPEAKER
A/B
LOUDNESS
INPUT
ATT.
Receiver
MAIN
SUB
SIGNAL
SELECT
TAPE 2
MONITOR
SYSTEM
SETUP
DISPLAY
DIMMER
VIDEO
SELECT
EFFECT/
CH SEL.
BASS/
TREBLE
TONE
•
The default setting is DUAL ch1.
•
You can only use this function with
Dolby Digital sources that have this
function.
•
When a DUAL MONO source is
being used the
Ò
&
Â
indicators
flash. Then, if you select DUAL ch1,
for example, the
Ò
indicator will light.
1
1