Yamaha CS6R Owner's Manual - Page 129
Part Settings for each Part, MIX Vce/Kit/Template, has been selected
View all Yamaha CS6R manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 129 highlights
Performance Mode Part (Settings for each Part) You can edit each Part in a Performance. Use Knob [A] to select the Part, then set its parameters. The following six screens are available, though their contents will vary according to the Part selected. • Part Mixer • Part Tone • Part Layer • Part Receive switch • Part Controller • Part Insertion Effect Part Mixer You can set various Voice output parameters for each Part. The following two screens are available. MIX Vce (Mix Voice) MIX Level The MIX Vce (Mix Voice) screen will change to the Mix Kit or Mix Template screen, respectively, if PartCL (Phrase Clip Part) or PartAD (A/D Input Part) has been selected. MIX Vce/Kit/Template (Mix Voice/Kit/Template) You can assign a Voice/Kit/Template to each Part. Use Knob [A] to select the Part, then set its Voice/Kit/Template parameters. The display will vary as follows according to the Part selected. • If Part01 to Part16 has been selected You can use the same method as the Category Search (Page 77) to set the Voice. MIXíVce) Memory Number Ctgry Search Part01 PRE1:128(H16)[Pf:GrandPiano] Use Knob [B] to select PLG1/2INT (internal memory) and the MSB/LSB (Plug-in Board's Bank), and use Knob [C] to select the Program Number. MIXíVce) Bank Number Ctgry Search PartP1 NORM/001:128(H16)[Pf:GrandPiano] s Bank t Settings: PartP1/P2 (Plug-in 1/2): PLG1/2 INT (Plug-in 1/2 Internal), MSB/LSB (Plug-in Bank) For details about Plug-in Banks (Bank Select MSB/LSB), refer to the Owner's Manual that came with your Plug-in Board. s Number (Program Number) t Settings: PLG1/2 INT (Plug-in 1/2 Internal): 1 ~ 64 MSB/LSB (Plug-in Bank): 1 ~ 128 There may be a delay when changing programs for Plug-in Parts (since voice data and default settings need to be sent). To change Voices for Plug-in Parts in a song, you should insert the Program Changes in the less data-intensive areas of the song. When selecting a Plug-in Board Voice, you should use the Program Number of the Parameter Change (multi-part). Details are given in the Owner's Manual that comes with the Plug-in Board. In Performance Mode, the Part assignments for Plug-in Boards are fixed at "16" for PLG1 and "15" for PLG2. For details about Plug-in Voices, refer to the Owner's Manual that came with your Plug-in Board. • If Part17 to Part32 has been selected You can set Voices for Parts 17 to 32 if you have a multitimbral Plug-in board installed. Use Knob [B] to select the Voice Bank and Knob [C] to select the Program Number. MIXíVce) Bank Number Part17 NORM/001:001(A01)[Pf:GrandPno] s Memory (Voice Memory) t Settings: PRE1 (Preset 1), PRE2 (Preset 2), INT (Internal Normal), EXT (External Normal), PRE (Preset Drum), INT (Internal Drum), EXT (External Drum) s Number (Program Number) t Settings: 1 ~ 128 (for Normal Voices), DR1 ~ DR8 (for Preset Drum), DR1 ~ DR2 (for Internal/External Drum) Details about Categories are given in the Category List on Page 80. s Bank/Number (Bank/Program Number) t Settings: Refer to the Owner's Manual that came with the Plug-in board. This setting is only held temporarily and cannot be stored with the Performance. • If PartCL (Phrase Clip Part) has been selected Select the Phrase Clip Kit used for the Phrase Clip Part. MIXíKit) PartCL Number 001(A01)[Dr:Clip Kit] • If PartP1/PartP2 (Plug-in 1/2) has been selected Set the Voice for the Plug-in 1/2 Part. This screen is only displayed if a Plug-in Board has been installed. s Number (Kit Number) t Settings: 1 ~ 4 129