Yamaha CS6R Owner's Manual - Page 156
PCLP VarAuto Variation Auto-set, PCLP VarRealTime Variation Real-time, PCLP Var Variation Manual
View all Yamaha CS6R manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 156 highlights
s Length Set the Variation length ratio. You can change the length of all the equal-sized sections by the amount set here. If you select "toEnd," the End Point of the source Phrase Clip will be used as the End Point of the Variation (after it has been divided). t Settings: toEnd, 10 ~ 800% If this setting is outside the End Point of the Phrase Clip, it will be automatically limited to the End Point setting. PCLP VarAuto (Variation Auto-set) The Start Point of the Variation is assigned automatically. The Loop and End Points are the same as those set in the original Phrase Clip. There may be cases that automatic setting is not available when the Clip has a narrow dynamic range (no big difference between loudest and smallest volume levels) because of the entire recorded level is too low, etc. At this screen, Variation Set 1 to 8 are assigned to each of the white notes of the keyboard in the range C3 to C4. Press each note to switch to the respective Variation Set, then set each Set's parameters. Finally, press the [ENTER] key to execute the Job. If you are not satisfied with the result, try repeating the process as you may get different results. PCLP VarAuto) Threshold Adjust Job C 2:001[SmplName] 255 -255 1At this screen, you can play back the currently selected Phrase Clip as a loop. 2Set the Start Points for Variations 1 to 8 by pressing notes C3 to C4 on the keyboard. By pressing the white notes (C3 to C4) on the keyboard corresponding to Variation Sets 1 to 8, you can set the Start Point while listening to the sound. 3In the same way, press the notes when setting the Start Points for the other Variation Sets. 4When you press the [EXIT] key, you will see the confirmation message. At this screen, you can verify by playing Variation Sets 1 to 8 by pressing the white notes on the keyboard between C3 and C4. 5Press the [INC/YES] key to set each Variation, or press the [DEC/NO] key to cancel the operation and return the Variation to its original state. PCLP Var (Variation Manual) You can change the settings for the Variation of the currently selected Phrase Clip. Use Knob [A] to select from Variation Sets 1 to 8 and use Knobs [B], [C], [1] and [2] to set its parameters. Then press the [ENTER] key to execute the Job. At this screen, the white notes on the keyboard between C3 and C4 can be used to select and play Variation Sets 1 to 8. Phrase Clip Mode s Threshold Set the threshold level at which the Auto-set process is started. The Start Point is automatically set when the average level of the Phrase Clip reaches or exceeds this value. t Settings: 0 ~ 255 s Adjust Set the amount by which the automatically-set Start Point is adjusted (moved forward). t Settings: -255 ~ 0 If the automatic setting is incorrect, Variation Set 1 will be set such that the entire length of the Phrase Clip will be played back. In this case the Start, Loop and End Points for Variation Sets 2 to 8 will be set to zero. PCLP VarRealTime (Variation Real-time) You can set the Start Point of the Variation in real-time while listening to the Loop. The Loop and End Points remain in the same positions as set for the Phrase Clip. The procedure is as follows. PCLP VarRealTime) Hit[C3-C4] [EXIT] Job C 2:001[SmplName] toVar1-8 toStop PCLP Var) Play Start Loop End Var=1: oneshot 2097150 2097150 2097150 s Var (Variation Number) Select the Variation you wish to set. The settings for the selected Variation will be reflected in all parameters. t Settings: 1 ~ 8 s Play (Play Mode) Select the Phrase Clip playback mode. There are three modes. t Settings: loop: When you press a note on the keyboard, the Phrase Clip is played completely from its Start Point. Then its looped section is played back repetitively until you release the note. oneshot: When you press a note on the keyboard, the Phrase Clip is played just once from its Start Point to its End Point (not looped). reverse: When you press a note on the keyboard, the Phrase Clip is played in reverse, just once, from its End Point to its Start Point (not looped). Basic details about each mode are given on Page 54. 156