Yamaha CS6R Owner's Manual - Page 130

Performance Mode • If PartAD (A/D Input Part) has been selected An audio source connected to the A/D INPUT jack can be used as a Part. There are 13 different templates for Effect Type and Gain settings. Select the A/D Input Part source and the template. MIXíTemplate)Src Number PartAD keybaord --[InsEF off ] s Src (Source) Select the source connected to the A/D INPUT jack. t Settings: mic (microphone), guitar, keyboard, audio s Number (Template Number) Select the Template Number. You can choose from 13 templates for each source. t Settings: 0 ~ 12 s Vol (Volume) Set the output level of the Part. t Settings: 0 ~ 127 s Pan Set the stereo pan position of the Part. t Settings: L63 (Left) ~ C (Center) ~ R63 (Right) s RevSend (Reverb Send) Set the Send level of the signal sent from Insertion Effect 1/2 (or the bypassed signal) to the Reverb effect. t Settings: 0 ~ 127 s ChoSend (Chorus Send) Set the Send level of the signal sent from Insertion Effect 1/2 (or the bypassed signal) to the Chorus effect. t Settings: 0 ~ 127 Number 0 Src MIC PresetName Off InputGain mic VariType - GUITAR PresetName Off InputGain mic VariType - KEYBOARD PresetName Off InputGain line VariType - AUDIO PresetName Off InputGain line VariType - 1 2 3 4 5 6 Mic Reverb mic mic - - Guitar mic - Reverb mic - Keyboard Reverb line line - - Audio line - Reverb line - Chorus mic - Chorus mic - Chorus line - Chorus line - Cho+Rev Karaoke1 Karaoke2 mic mic mic - Karaoke1 Karaoke2 Cho+Rev Tube Stack mic mic mic - AmpSim. AmpSim. Cho+Rev PhaserEP PanEP line line line - Phaser1 AutoPan Cho+Rev Audio line line - - Audio line - Number Src 7 8 9 10 11 12 MIC PresetName Karaoke3 Echo Vocal Studio OctUp OctDown InputGain mic mic mic mic mic mic VariType Karaoke3 Echo Stage1 Exciter PitChange1 PitChange1 GUITAR PresetName FlangGtr CleanGtr FuncGtr Tremolo Phaser 5thGuitar InputGain mic mic mic mic mic mic VariType Flanger1 Celeste3 TouchWah2 Tremolo Phaser1 PitChange1 KEYBOARD PresetName WahClavi RotaryOrg SynthStr SynthPad SynthLead SFX InputGain line line line line line line VariType TouchWah1 RotarySp. Symphonic Flanger2 DelayLCR PitChange1 AUDIO PresetName Audio InputGain line VariType - Audio line - Audio line - Audio line - Audio line - Audio line - If the InsEF parameter of the EFF Part screen is set to something other than PartAD, "InsEF Off" will be displayed and this parameter will not be available. MIX Level You can set output level, pan, effect send and other parameters for each Part. This is useful when setting up the levels of each Part in a mix. MIXíLevel) Vol Part01 127 Pan RevSend ChoSend C 64 0 Part Tone You can set Filter, Envelope Generator and other parameters controlling the tonal characteristics of each Part. The following four screens are available. TON Filter (Tone Filter) TON EG (Tone Envelope Generator) TON Portamento (Tone Portamento) TON Other (Tone Other) TON Filter (Tone Filter) You can use filters to adjust the tone of each part. If the filter is an LPF and HPF combination, the Cutoff parameter applies to the LPF. TONíFilter) Part01 Cutoff +63 Reso +63 This screen is not available for the A/D Input Part. Details about the Filter are given on Page 93. s Cutoff Raise or lower the Cutoff frequency for each Element of a Part. For each Element, if a combined Low Pass and High Pass Filter is being used, this parameter adjusts the Cutoff frequency of the Low Pass Filter. t Settings: -64 ~ 0 ~ +63 130