Dell OptiPlex Gs Reference and Installation Guide (.pdf) - Page 96

Table A-1., Configuration Utility Messages, No Configuration Man

Get Dell OptiPlex Gs PDF manuals and user guides View all Dell OptiPlex Gs manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

Table A-1. Configuration Utility Messages (Continued) Message Probable Cause Corrective Action No Configuration Manager. The device driver needed by the ICU is corrupted or is not correctly configured. Verify that the following device statement appears in your config.sys file: device=drive:\directory\drivers\dos\dwcfgmg.sys In this statement, drive and directory represent the drive and directory where the driver resides. The default is c:\plugplay. At least one Plug and Play card in your system is not configured due to conflicts. These are marked "config err" in the list of configured cards. Due to conflicts, the ICU could only configure some Plug and Play cards in your system. Unconfigured cards are marked "config err" in the list of configured cards. The Configuration Manager or the ICU cannot configure at least one Plug and Play expansion card because of resource conflicts with one or more cards. You must reconfigure the conflicting card(s). To find the conflicting card, perform the following steps: 1. Select the Plug and Play expansion card marked with config err, and then click the Modify button. The Card Configuration dialog box displays the functions assigned to the Plug and Play expansion card. 2. Select a function and then click the Settings button. Click the Cancel button if the ICU does not display a message naming the conflicting card. 3. Repeat step 2 until the ICU displays a message box naming the conflicting card and the resource(s) in conflict. See the following table entry for an explanation of this message box. This device is unconfigurable because of a resource conflict with card card_name. The conflicting resource is resource_name. To fix, reconfigure the conflicting card. The selected card is unconfigurable because one of its resources is already being used by another device. Perform the following procedure: 1. Make a note of the card name and the type of conflicting resource. 2. Follow the procedure in "Modifying a Card" in Chapter 3, and change the value for resource_name used by card_name. NOTE: For the full name of an abbreviation or acronym used in this table, see the Glossary in your online System User's Guide. A-2 Dell OptiPlex Gs and Gs+ Low-Profile Systems Reference and Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
A-2
Dell OptiPlex Gs and Gs+ Low-Profile Systems Reference and Installation Guide
No Configuration Man-
ager.
The device driver needed by
the ICU is corrupted or is
not correctly configured.
Verify that the following
device
statement
appears in your
config.sys
file:
device=
drive
:\
directory
\driv-
ers\dos\dwcfgmg.sys
In this statement,
drive
and
directory
represent the
drive and directory where the driver resides. The
default is
c:\plugplay
.
At least one Plug and
Play card in your sys-
tem is not configured
due to conflicts.
These are marked “con-
fig err” in the list
of configured cards.
Due to conflicts, the
ICU could only config-
ure some Plug and Play
cards in your system.
Unconfigured cards are
marked “config err” in
the list of configured
cards.
The Configuration Manager
or the ICU cannot configure
at least one Plug and Play
expansion card because of
resource conflicts with one
or more cards.
You must reconfigure the conflicting card(s).
To find the conflicting card, perform the fol-
lowing steps:
1.
Select the Plug and Play expansion card
marked with
config err
, and then click
the Modify button.
The Card Configuration dialog box dis-
plays the functions assigned to the Plug
and Play expansion card.
2.
Select a function and then click the Set-
tings button. Click the Cancel button if
the ICU does not display a message naming
the conflicting card.
3.
Repeat step 2 until the ICU displays a
message box naming the conflicting card
and the resource(s) in conflict. See the
following table entry for an explanation
of this message box.
This device is un-
configurable because
of a resource conflict
with card
card_name
.
The conflicting
resource is
resource_name
. To fix,
reconfigure the con-
flicting card.
The selected card is un-
configurable because one of
its resources is already being
used by another device.
Perform the following procedure:
1.
Make a note of the card name and the
type of conflicting resource.
2.
Follow the procedure in “Modifying a
Card” in Chapter 3, and change the
value for
resource_name
used by
card_name
.
Table A-1.
Configuration Utility Messages
(Continued)
Message
Probable Cause
Corrective Action
NOTE: For the full name of an abbreviation or acronym used in this table, see the Glossary in your online
System User’s Guide
.