Dell PowerEdge SC440 Hardware Owner's Manual  - Page 105

Open the system. See Opening the System on Turn off the system

Get Dell PowerEdge SC440 PDF manuals and user guides View all Dell PowerEdge SC440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

3 Move the PSWD jumper to the disabled position. See Figure 6-1 to locate the password jumper on the system board. 4 Close the system. See "Closing the System" on page 41. 5 Reconnect the system to the electrical outlet, and turn on the system. The existing passwords are not disabled (erased) until the system boots with the password jumper plug removed. However, before you assign a new system and/or setup password, you must install the jumper plug. NOTE: If you assign a new system and/or setup password with the jumper plug still removed, the system disables the new password(s) the next time it boots. 6 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet. 7 Open the system. See "Opening the System" on page 41. 8 Move the PSWD jumper from the disabled position to the enabled position. 9 Close the system, reconnect the system to the electrical outlet, and turn on the system. 10 Assign a new system and/or setup password. To assign a new password using the System Setup program, see "Using the System Password" on page 35. Jumpers and Connectors 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
Jumpers and Connectors
105
3
Move the PSWD jumper to the disabled position.
See Figure 6-1 to locate the password jumper on the system board.
4
Close the system. See "Closing the System" on page 41.
5
Reconnect the system to the electrical outlet, and turn on the system.
The existing passwords are not disabled (erased) until the system boots with the password jumper plug
removed. However, before you assign a new system and/or setup password, you must install the jumper
plug.
NOTE:
If you assign a new system and/or setup password with the jumper plug still removed, the system
disables the new password(s) the next time it boots.
6
Turn off the system, including any attached peripherals, and disconnect the system from the electrical
outlet.
7
Open the system. See "Opening the System" on page 41.
8
Move the PSWD jumper from the disabled position to the enabled position.
9
Close the system, reconnect the system to the electrical outlet, and turn on the system.
10
Assign a new system and/or setup password.
To assign a new password using the System Setup program, see "Using the System Password" on
page 35.