Dell PowerEdge SC440 Hardware Owner's Manual  - Page 71

Chassis Intrusion Switch, Removing the Chassis Intrusion Switch

Get Dell PowerEdge SC440 PDF manuals and user guides View all Dell PowerEdge SC440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

• P7 to the diskette drive • P8, P9, and P10 to the optical and tape drives 7 Close the system. See "Closing the System" on page 41. Chassis Intrusion Switch Removing the Chassis Intrusion Switch CAUTION: Only trained service technicians are authorized to remove the system cover and access any of the components inside the system. Before performing any procedure, see your Product Information Guide for complete information about safety precautions, working inside the computer and protecting against electrostatic discharge. 1 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet. 2 Open the system. See "Opening the System" on page 41. 3 Disconnect the chassis intrusion switch cable from the INTRUDER connector on the system board. See Figure 3-20. 4 Slide the chassis intrusion switch out of the securing bracket notch. See Figure 3-20. 5 Remove the switch and its attached cable from the system. Installing System Components 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
Installing System Components
71
•
P7 to the diskette drive
•
P8, P9, and P10 to the optical and tape drives
7
Close the system. See "Closing the System" on page 41.
Chassis Intrusion Switch
Removing the Chassis Intrusion Switch
CAUTION:
Only trained service technicians are authorized to remove the system cover and access any of the
components inside the system. Before performing any procedure, see your
Product Information Guide
for
complete information about safety precautions, working inside the computer and protecting against electrostatic
discharge.
1
Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.
2
Open the system. See "Opening the System" on page 41.
3
Disconnect the chassis intrusion switch cable from the INTRUDER connector on the system board.
See Figure 3-20.
4
Slide the chassis intrusion switch out of the securing bracket notch. See Figure 3-20.
5
Remove the switch and its attached cable from the system.