Home » HP Manuals » Servers » HP Cluster Platform Interconnects v2010 » Manual Viewer

HP Cluster Platform Interconnects v2010 HP Cluster Platform InfiniBand Interco - Page 36

Installing the ISR 9024 Power Supply Unit, 2.5 Operating the ISR 9024 Interconnect

Get HP Cluster Platform Interconnects v2010 PDF manuals and user guides

View all HP Cluster Platform Interconnects v2010 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

2.4 Installing the ISR 9024 Power Supply Unit An ISR 9024 contains either one or two power supplies in the side bays of the unit chassis, as shown in Figure 2-3. Warning: To maintain the correct cooling air flow, you must fill an unused power supply bay by using the supplied blank filler panel Use the following procedure to install or remove a power supply. You can do this when the interconnect is running 1. Unscrew the captive fasteners at each side of the filler panel and remove it from the front panel. Retain the filler panel for future use. 2. Position the rear (connector end) of the power supply in the empty bay. 3. Holding the power supply level with the chassis, slide it into the slot until it meets resistance at the chassis connector. Do not force the unit if you feel resistance, ensure that it is level and square with the bay. 4. Push the module further until it is completely seated on the connector, and its bezel is flush with the chassis front panel. 5. Use the captive fasteners at each side of the power supply to secure it in place. 2.5 Operating the ISR 9024 Interconnect To power up the interconnect and begin using it, use the following procedure: 1. Ensure that the following tasks are complete: a. The chassis is secured in the rack. b. Cabling is complete as described in Chapter 7. c. If not already connected, connect a power supply cable to the IEC inlets for each PSU installed (maximum two cables) to the adjacent power strip outlets located in the sides of the rack. d. All other cluster components are installed, cabled, and powered up. 2. Apply power to the interconnect, and verify the following LED status: a. The green power supply indicators at the front panel are illuminated. b. The green status LED on the front panel that is labelled SYS is illuminated. c. The green status LED on the front panel that is labelled SM is illuminated as follows: • Constant, for active mode. • Flashing, for standby mode. d. The green status LED on the front panel that is labelled PS is illuminated. 3. For each port that has a connected InfiniBand link cable: a. The green physical link LED is illuminated. b. The amber logical link LED is illuminated in one of the following states: • Constant, indicating the presence of a link with no data traffic passing over the link • Flashing, indicating the presence of a link with data traffic passing over the link. 2.6 Troubleshooting the ISR 9024 If any indicators are not illuminated as described in the preceding list, use the following verification procedure: 1. The PS LED does not illuminate. 2. The PSU is faulty. Replace the PSU. 36 Installing and Maintaining the ISR 9024 Interconnect

Section	Page
InfiniBand Interconnect Installation and User's Guide	1
Table of Contents	3
About This Manual	11
Organization	11
Audience	12
Related Documentation	12
Voltaire Documentation	12
HP Cluster Platform Documentation	12
Cluster Component Documentation	13
HP Encourages Your Comments	13
Text Annotations	13
Conventions	14
Safety Considerations	15
Information on Ergonomics	16
Recycling	17
1 InfiniBand Technology Overview	19
1.1 Identifying InfiniBand Fabric Components	20
1.2 ISR 9xxxx-series Interconnects	21
1.3 Identifying the ISR 9024 Interconnect (SDR)	22
1.4 Identifying the ISR 9024 S/D Interconnect (RoHS Compliant)	22
1.5 Identifying the ISR 9096 Interconnect	23
1.6 Identifying the ISR 9288 Interconnect	24
1.7 Understanding the Interconnect Management Capabilities	26
2 Installing and Maintaining the ISR 9024 Interconnect	29
2.1 Overview of the ISR 9024 Interconnect	29
2.1.1 Internally Managed ISR 9024 Front Panel	30
2.1.2 ISR 9024 Management Card	31
2.1.3 Externally Managed ISR 9024 Front Panel	32
2.1.4 ISR 9024 Rear Panel	32
2.1.5 Cooling and Airflow	33
2.2 Unpacking the ISR 9024 Interconnect	33
2.3 Mounting the ISR 9024 in the Rack	34
2.4 Installing the ISR 9024 Power Supply Unit	36
2.5 Operating the ISR 9024 Interconnect	36
2.6 Troubleshooting the ISR 9024	36
3 Installing and Maintaining the ISR 9024 S/D Interconnect (RoHS Compliant)	39
3.1 Overview of the ISR 9024 S/D Interconnect	39
3.1.1 Internally Managed ISR 9024 S/D–M Front Panel	40
3.1.1.1 ISR 9024S/D-M Management Card	41
3.1.2 Externally Managed ISR 9024 S/D Front Panel	41
3.1.3 ISR 9024 S/D Rear Panel	42
3.2 Unpacking the ISR 9024 S/D Interconnect	43
3.3 Mounting the ISR 9024 S/D in the Rack	44
3.4 The ISR 9024 S/D Fan Unit	45
3.4.1 Replacing the Fan Unit	46
3.5 Installing the ISR 9024 S/D Power Supply Units	46
3.6 Operating the ISR 9024 S/D Interconnect	47
3.7 Troubleshooting the ISR 9024 S/D	47
4 Installing and Maintaining the ISR 9096 and ISR 9288 Interconnects	49
4.1 Overview of the ISR 9XXX Interconnects	49
4.1.1 ISR ISR 9XXX Interconnect Features	49
4.1.2 ISR ISR 9XXX Interconnect Architecture	50
4.1.3 ISR ISR 9XXX Building Blocks	50
4.1.3.1 Field Replaceable Units	51
4.1.4 ISR ISR 9XXX System Firmware	51
4.1.5 ISR ISR 9XXX Control Panels and Reset Buttons	52
4.2 Unpacking the Chassis	52
4.2.1 Unpacking the ISR 9288	53
4.2.2 Unpacking the ISR 9096	55
4.2.3 Verifying the Shipment	56
4.3 Repacking the Chassis	58
4.4 Mounting the ISR 9XXX in the Rack	58
4.4.1 Resources Required to Perform an Installation	59
4.4.2 Mounting The Chassis in the Rack	59
4.4.3 Installing the Cabling Clamps	63
4.5 Standard Configurations	63
4.6 Post-installation Tasks	67
5 HP 4x DDR IB Switch Module for c-Class BladeSystems Overview	69
5.1 Installing the 4x DDR IB Switch Module	69
5.1.1 Subnet Manager	70
6 Installing Field-Replaceable Units in the ISR 9XXX Chassis	71
6.1 Guidelines for Inserting and Extracting Boards	71
6.2 Installing or Replacing the sFB-12 Fabric Board	72
6.3 Installing or Replacing sLB-24 Line Boards	73
6.4 Installing or Replacing the sMB (Management) Board	75
6.5 Installing and Replacing Power Supply Units	76
6.6 Populating the Router Blade Drawer (sRBD)	77
6.6.1 Overview of the IPR (TCP/IP) Blade	77
6.6.2 Overview of the FCR (Fibre Channel Router) Blade	78
6.6.3 Installing a Router Blade	79
6.7 Installing or Replacing the Router Blade Drawer (sRBD)	80
6.8 Installing and Replacing the sCTRL Board	81
6.9 Installing the sFU-4 Fan Module	82
6.10 Installing the sFU-8 Fan Module	83
7 Cabling the Interconnect	85
7.1 InfiniBand Cabling	85
7.1.1 General InfiniBand Cabling Guidelines	85
7.1.2 Cabling Tables	86
7.1.3 Connecting InfiniBand Cables	86
7.1.4 Cable Routing Procedure for the ISR 9024 or ISR 9024 S/D	86
7.1.5 Cable Routing Procedure for the ISR 9096	87
7.1.6 Connecting the ISR 9096 Router Blades	88
7.1.6.1 Connecting to IPR GbE Ports	88
7.1.6.2 Connecting to FCR FC Ports	88
7.1.7 Cable Routing Procedure for the ISR 9288	88
7.2 Connecting the ISR 9288 Router Blades	89
7.2.1 Connecting to IPR GbE Ports	89
7.2.2 Connecting to FCR FC Ports	90
7.3 Chassis Administrative Connections	90
7.3.1 Cabling the ISR 9024 Management Connections	90
7.3.2 Cabling the ISR 9096 and the ISR 9288 Management Connections	90
7.3.3 Connecting the Management Port Serial Interface	91
8 Installing and Maintaining HCA Cards and Mezzanines	93
8.1 Overview of the Voltaire HCA 400 PCI–X, and HCA 400 PCI-Express Cards	93
8.2 Installing the HCA	94
8.3 Topspin/Mellanox PCI-X HCA	97
8.4 Topspin/Mellanox PCI-Express HCA	98
8.5 Mellanox PCI-X HCA (SDR)	99
8.5.1 Mellanox PCI-X SDR HCA LEDs	99
8.6 Mellanox PCI-Express HCA (SDR)	100
8.6.1 Mellanox PCI-Express SDR HCA LEDs	100
8.7 Mellanox Memory Free PCI-Express HCA (SDR)	101
8.7.1 LEDs	102
8.8 Mellanox Memory Free PCI-Express HCA (DDR)	102
8.8.1 LEDs	103
8.9 Mellanox PCI-Express HCA (DDR)	103
8.9.1 Mellanox PCI-Express DDR HCA LEDs	104
8.9.2 HP HPC 4x DDR IB Mezzanine HCA	105
8.9.3 Operating System and Software Requirements	105
9 Postinstallation Troubleshooting and Diagnostics	107
9.1 Postinstallation Troubleshooting	107
9.2 Startup Checks for the ISR 9XXX	107
9.3 Debugging a Fabric Failure by Using Performance Management (PM)	108
9.4 Identifying a Leaf or Spine Port Malfunction on an ISR 9XXX	108
9.5 Detecting a Failed Port	108
A ISR 9024 Interconnect Specifications	111
B ISR 9024 S/D Interconnect Specifications (RoHS Compliant)	113
C ISR 9096 Interconnect Specifications	117
D ISR 9288 Interconnect Specifications	119
E 4x DDR IB Switch Module Specifications	123
F HCA PCI Card Specifications	125
F.1 Voltaire HCA–400 PCI Card Specifications	125
F.2 Topspin/Mellanox PCI-X HCA Specifications	126
F.3 Topspin/Mellanox PCI-Express HCA Specifications	127
F.4 Mellanox PCI-X HCA Specifications	128
F.5 Mellanox PCI-Express HCA Specifications	128
F.6 Mellanox Memory Free PCI-Express HCA (SDR) Specifications	129
F.7 Mellanox Memory Free PCI-Express HCA (DDR) Specifications	129
F.8 Mellanox PCI-Express DDR HCA Specifications	130
F.9 HPC 4x DDR IB Mezzanine HCA Specifications	130

Match case Limit results 1 per page

2.4 Installing the ISR 9024 Power Supply Unit

An ISR 9024 contains either one or two power supplies in the side bays of the unit chassis, as

shown in

Figure 2-3

Warning:

To maintain the correct cooling air flow, you must fill an unused power supply bay by using the

supplied blank filler panel

Use the following procedure to install or remove a power supply. You can do this when the

interconnect is running

Unscrew the captive fasteners at each side of the filler panel and remove it from the front

panel. Retain the filler panel for future use.

Position the rear (connector end) of the power supply in the empty bay.

Holding the power supply level with the chassis, slide it into the slot until it meets resistance

at the chassis connector. Do not force the unit if you feel resistance, ensure that it is level

and square with the bay.

Push the module further until it is completely seated on the connector, and its bezel is flush

with the chassis front panel.

Use the captive fasteners at each side of the power supply to secure it in place.

2.5 Operating the ISR 9024 Interconnect

To power up the interconnect and begin using it, use the following procedure:

Ensure that the following tasks are complete:

The chassis is secured in the rack.

Cabling is complete as described in

Chapter 7

If not already connected, connect a power supply cable to the IEC inlets for each PSU

installed (maximum two cables) to the adjacent power strip outlets located in the sides

of the rack.

All other cluster components are installed, cabled, and powered up.

Apply power to the interconnect, and verify the following LED status:

The green power supply indicators at the front panel are illuminated.

The green status LED on the front panel that is labelled SYS is illuminated.

The green status LED on the front panel that is labelled SM is illuminated as follows:

•

Constant, for active mode.

•

Flashing, for standby mode.

The green status LED on the front panel that is labelled PS is illuminated.

For each port that has a connected InfiniBand link cable:

The green physical link LED is illuminated.

The amber logical link LED is illuminated in one of the following states:

•

Constant, indicating the presence of a link with no data traffic passing over the

link

•

Flashing, indicating the presence of a link with data traffic passing over the link.

2.6 Troubleshooting the ISR 9024

If any indicators are not illuminated as described in the preceding list, use the following

verification procedure:

The PS LED does not illuminate.

The PSU is faulty. Replace the PSU.

Installing and Maintaining the ISR 9024 Interconnect