HP Cluster Platform Interconnects v2010 HP Cluster Platform InfiniBand Interco - Page 45

3.

Attach the front L-brackets to either side of the chassis, using the three 8/32-in screws

provided, as shown by callout 1 in

Figure 3-5

.

4.

Attach the rear L-brackets loosely to each rail, as shown by callout 2 in

Figure 3-5

. The screws

should be just loose enough that you can easily adjust the position of the bracket on the rail.

Position the L-bracket so that the fasteners are approximately in the centre of the elongated

holes.

5.

The distance between the rack columns is 29.2 inches. Align the left rail with the side of the

chassis, so that the distance between the L-brackets is approximately 29.2 inches, within the

L-bracket's range of adjustment.

6.

Align the holes in the rail with the four threaded holes in the chassis, as shown by callout 3

in

Figure 3-5

, and secure the rail to the chassis using four 8/32-in screws provided. Start at

the eighth hole from the front-facing the end of the bracket. Callout 4 indicates the

interconnect's front panel, depending on the model, the panels are shown in

Figure 3-2

and

Figure 3-1

.

7.

Verify that the distance between the two brackets is approximately 29.2 inches, and within

the L-bracket's range of adjustment.

8.

Repeat steps 2–4 for the right rail.

9.

For each bracket, clip two M6 cage nuts into the back of each of the four rack columns, at

the appropriate U-location. Ensure that you install a total of eight M6 cage nuts.

10.

Working at the front of the rack, lift and slide the chassis into its location and secure the

front L-brackets to the cage nuts by using four M6 machine screws. Torque each screw to

30-in/lb.

11.

Working at the rear of the rack, adjust the position of the rear L-brackets, and secure them

to the cage nuts by using four M6 machine screws. Torque each screw to 30-in/lb.

12.

Tighten the screws that secure the rear L-bracket to the track, and verify that all fasteners

are tight.

13.

How you power up your interconnect depends on the current state of the cluster and the

requirements of the operating environment. If the cluster is not running, you are now ready

to cable the interconnect, following the cabling instructions in

Chapter 7

, and using the

following sequence:

a.

InfiniBand cables, which must be connected according to the port address specifications

for your cluster.

b.

Communications cables, such as the DB9 serial console cable or a CAT-V Ethernet cable.

c.

The power cord.

d.

The power-up procedures in the operating environment.

After installing an interconnect, your first task is usually to determine that the interconnect and

its links are correctly cabled and are functioning. Consult the interconnect diagnostics chapter

to run the appropriate tests. Next, boot the operating system and run any diagnostics required

to confirm the operation of the interconnect in the cluster. See the

Voltaire InfiniBand Fabric

Management and Diagnostic Guide

.

3.4 The ISR 9024 S/D Fan Unit

The ISR 9024 S/D has a hot swappable field replaceable fan unit that includes two fans and

provides active front-to-rear air-flow cooling as well as full redundancy. A single fan can serve

the entire product cooling requirements. Auto heat sensing allows for silent fan operation. Normal

and Turbo are supported modes for higher MTBF and better acoustic noise. If there is a failure

or a high temperature is sensed, the fans are set to Turbo mode. The ISR 9024 S/D temperature

control fan rate threshold algorithm is as follows:

•

Fans in normal mode temperature range: 25ºC -84ºC (on switch chip)

•

Fans in Turbo mode: 85ºC (on switch chip)

•

95ºC (on switch chip) – the system shuts down

3.4 The ISR 9024 S/D Fan Unit

45

Section	Page
InfiniBand Interconnect Installation and User's Guide	1
Table of Contents	3
About This Manual	11
Organization	11
Audience	12
Related Documentation	12
Voltaire Documentation	12
HP Cluster Platform Documentation	12
Cluster Component Documentation	13
HP Encourages Your Comments	13
Text Annotations	13
Conventions	14
Safety Considerations	15
Information on Ergonomics	16
Recycling	17
1 InfiniBand Technology Overview	19
1.1 Identifying InfiniBand Fabric Components	20
1.2 ISR 9xxxx-series Interconnects	21
1.3 Identifying the ISR 9024 Interconnect (SDR)	22
1.4 Identifying the ISR 9024 S/D Interconnect (RoHS Compliant)	22
1.5 Identifying the ISR 9096 Interconnect	23
1.6 Identifying the ISR 9288 Interconnect	24
1.7 Understanding the Interconnect Management Capabilities	26
2 Installing and Maintaining the ISR 9024 Interconnect	29
2.1 Overview of the ISR 9024 Interconnect	29
2.1.1 Internally Managed ISR 9024 Front Panel	30
2.1.2 ISR 9024 Management Card	31
2.1.3 Externally Managed ISR 9024 Front Panel	32
2.1.4 ISR 9024 Rear Panel	32
2.1.5 Cooling and Airflow	33
2.2 Unpacking the ISR 9024 Interconnect	33
2.3 Mounting the ISR 9024 in the Rack	34
2.4 Installing the ISR 9024 Power Supply Unit	36
2.5 Operating the ISR 9024 Interconnect	36
2.6 Troubleshooting the ISR 9024	36
3 Installing and Maintaining the ISR 9024 S/D Interconnect (RoHS Compliant)	39
3.1 Overview of the ISR 9024 S/D Interconnect	39
3.1.1 Internally Managed ISR 9024 S/D–M Front Panel	40
3.1.1.1 ISR 9024S/D-M Management Card	41
3.1.2 Externally Managed ISR 9024 S/D Front Panel	41
3.1.3 ISR 9024 S/D Rear Panel	42
3.2 Unpacking the ISR 9024 S/D Interconnect	43
3.3 Mounting the ISR 9024 S/D in the Rack	44
3.4 The ISR 9024 S/D Fan Unit	45
3.4.1 Replacing the Fan Unit	46
3.5 Installing the ISR 9024 S/D Power Supply Units	46
3.6 Operating the ISR 9024 S/D Interconnect	47
3.7 Troubleshooting the ISR 9024 S/D	47
4 Installing and Maintaining the ISR 9096 and ISR 9288 Interconnects	49
4.1 Overview of the ISR 9XXX Interconnects	49
4.1.1 ISR ISR 9XXX Interconnect Features	49
4.1.2 ISR ISR 9XXX Interconnect Architecture	50
4.1.3 ISR ISR 9XXX Building Blocks	50
4.1.3.1 Field Replaceable Units	51
4.1.4 ISR ISR 9XXX System Firmware	51
4.1.5 ISR ISR 9XXX Control Panels and Reset Buttons	52
4.2 Unpacking the Chassis	52
4.2.1 Unpacking the ISR 9288	53
4.2.2 Unpacking the ISR 9096	55
4.2.3 Verifying the Shipment	56
4.3 Repacking the Chassis	58
4.4 Mounting the ISR 9XXX in the Rack	58
4.4.1 Resources Required to Perform an Installation	59
4.4.2 Mounting The Chassis in the Rack	59
4.4.3 Installing the Cabling Clamps	63
4.5 Standard Configurations	63
4.6 Post-installation Tasks	67
5 HP 4x DDR IB Switch Module for c-Class BladeSystems Overview	69
5.1 Installing the 4x DDR IB Switch Module	69
5.1.1 Subnet Manager	70
6 Installing Field-Replaceable Units in the ISR 9XXX Chassis	71
6.1 Guidelines for Inserting and Extracting Boards	71
6.2 Installing or Replacing the sFB-12 Fabric Board	72
6.3 Installing or Replacing sLB-24 Line Boards	73
6.4 Installing or Replacing the sMB (Management) Board	75
6.5 Installing and Replacing Power Supply Units	76
6.6 Populating the Router Blade Drawer (sRBD)	77
6.6.1 Overview of the IPR (TCP/IP) Blade	77
6.6.2 Overview of the FCR (Fibre Channel Router) Blade	78
6.6.3 Installing a Router Blade	79
6.7 Installing or Replacing the Router Blade Drawer (sRBD)	80
6.8 Installing and Replacing the sCTRL Board	81
6.9 Installing the sFU-4 Fan Module	82
6.10 Installing the sFU-8 Fan Module	83
7 Cabling the Interconnect	85
7.1 InfiniBand Cabling	85
7.1.1 General InfiniBand Cabling Guidelines	85
7.1.2 Cabling Tables	86
7.1.3 Connecting InfiniBand Cables	86
7.1.4 Cable Routing Procedure for the ISR 9024 or ISR 9024 S/D	86
7.1.5 Cable Routing Procedure for the ISR 9096	87
7.1.6 Connecting the ISR 9096 Router Blades	88
7.1.6.1 Connecting to IPR GbE Ports	88
7.1.6.2 Connecting to FCR FC Ports	88
7.1.7 Cable Routing Procedure for the ISR 9288	88
7.2 Connecting the ISR 9288 Router Blades	89
7.2.1 Connecting to IPR GbE Ports	89
7.2.2 Connecting to FCR FC Ports	90
7.3 Chassis Administrative Connections	90
7.3.1 Cabling the ISR 9024 Management Connections	90
7.3.2 Cabling the ISR 9096 and the ISR 9288 Management Connections	90
7.3.3 Connecting the Management Port Serial Interface	91
8 Installing and Maintaining HCA Cards and Mezzanines	93
8.1 Overview of the Voltaire HCA 400 PCI–X, and HCA 400 PCI-Express Cards	93
8.2 Installing the HCA	94
8.3 Topspin/Mellanox PCI-X HCA	97
8.4 Topspin/Mellanox PCI-Express HCA	98
8.5 Mellanox PCI-X HCA (SDR)	99
8.5.1 Mellanox PCI-X SDR HCA LEDs	99
8.6 Mellanox PCI-Express HCA (SDR)	100
8.6.1 Mellanox PCI-Express SDR HCA LEDs	100
8.7 Mellanox Memory Free PCI-Express HCA (SDR)	101
8.7.1 LEDs	102
8.8 Mellanox Memory Free PCI-Express HCA (DDR)	102
8.8.1 LEDs	103
8.9 Mellanox PCI-Express HCA (DDR)	103
8.9.1 Mellanox PCI-Express DDR HCA LEDs	104
8.9.2 HP HPC 4x DDR IB Mezzanine HCA	105
8.9.3 Operating System and Software Requirements	105
9 Postinstallation Troubleshooting and Diagnostics	107
9.1 Postinstallation Troubleshooting	107
9.2 Startup Checks for the ISR 9XXX	107
9.3 Debugging a Fabric Failure by Using Performance Management (PM)	108
9.4 Identifying a Leaf or Spine Port Malfunction on an ISR 9XXX	108
9.5 Detecting a Failed Port	108
A ISR 9024 Interconnect Specifications	111
B ISR 9024 S/D Interconnect Specifications (RoHS Compliant)	113
C ISR 9096 Interconnect Specifications	117
D ISR 9288 Interconnect Specifications	119
E 4x DDR IB Switch Module Specifications	123
F HCA PCI Card Specifications	125
F.1 Voltaire HCA–400 PCI Card Specifications	125
F.2 Topspin/Mellanox PCI-X HCA Specifications	126
F.3 Topspin/Mellanox PCI-Express HCA Specifications	127
F.4 Mellanox PCI-X HCA Specifications	128
F.5 Mellanox PCI-Express HCA Specifications	128
F.6 Mellanox Memory Free PCI-Express HCA (SDR) Specifications	129
F.7 Mellanox Memory Free PCI-Express HCA (DDR) Specifications	129
F.8 Mellanox PCI-Express DDR HCA Specifications	130
F.9 HPC 4x DDR IB Mezzanine HCA Specifications	130

HP Cluster Platform Interconnects v2010 HP Cluster Platform InfiniBand Interco - Page 45

The ISR 9024 S/D Fan Unit

Page 45 highlights