HP ProLiant DL170e HP ProLiant DL170e G6 Server Maintenance and Service Guide - Page 103

Removal and replacement procedures

Get HP ProLiant DL170e - G6 Server PDF manuals and user guides View all HP ProLiant DL170e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

Figure 87 Installing the Onboard SATA Cable Guard/Battery Holder on the 2U Node 13. Align the 2U bottom plastic air baffle to the system board. Make sure the tab is aligned to the slot. 14. Put the tabs of the 2U bottom plastic air baffle in the slots of the system board tray. Figure 88 Installing the 2U Bottom Plastic Air Baffle 15. Remove the card holder bracket away from the 2U PCIe cage as Figure 50. 16. Loosen and remove the screw to release the slot cover from the 2U PCIe cage. 17. Remove slot cover from the 2U PCIe cage. In this document, we remove the low-profile slot cover of the 2U PCIe cage as example since the primary location for the smart array P212 controller board on the 2U riser card should always be the lowest connector (the low-profile connector). Removal and replacement procedures 103

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
Removal and replacement procedures
103
Figure 87
Installing the Onboard SATA Cable Guard/Battery Holder on the 2U Node
13.
Align the 2U bottom plastic air baffle to the system board. Make sure the tab is aligned to the
slot.
14.
Put the tabs of the 2U bottom plastic air baffle in the slots of the system board tray.
Figure 88
Installing the 2U Bottom Plastic Air Baffle
15.
Remove the card holder bracket away from the 2U PCIe cage as Figure 50.
16.
Loosen and remove the screw to release the slot cover from the 2U PCIe cage.
17.
Remove slot cover from the 2U PCIe cage.
In this document, we remove the low-profile slot cover of the 2U PCIe cage as example since the
primary location for the smart array P212 controller board on the 2U riser card should always
be the lowest connector (the low-profile connector).