HP ProLiant DL170e HP ProLiant DL170e G6 Server Maintenance and Service Guide - Page 104

Removal and replacement procedures, Removing the Slot Cover from the 2U PCIe Cage

Get HP ProLiant DL170e - G6 Server PDF manuals and user guides View all HP ProLiant DL170e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

Figure 89 Removing the Slot Cover from the 2U PCIe Cage 18. Remove the originally attached bracket from the smart array P212 controller board (for removing methods of the originally attached bracket, please refer to the Figure 73 in this document). 19. Install the low-profile vented bracket on the smart array P212 controller board (for installation methods of the low-profile vented bracket, please refer to the Figure 74 in this document). There are two types of vented brackets for the smart array P212 controller board: low-profile and full-height. The low-profile vented bracket is for the smart array P212 controller board to be installed on the low-profile riser card connector. The full-height vented bracket is for smart array P212 controller board installed on the full-height riser card connector. In this document we install the low-profile vented bracket for P212 as example since the primary location for P212 on the riser card should always be the lowest connector (the low-profile connector). However, the following installation methods of the full-height vented bracket can be taken as reference when you install P212 installed on the full-height riser card connector: a. Insert the smart array P212 controller board to the matching slot on the full-height vented bracket. Make sure the smart array P212 controller board is aligned to the full-height vented bracket by the 2 screw holes. b. Install the 2 screws to install the full-height vented bracket to smart array P212 controller board. Removal and replacement procedures 104

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
Removal and replacement procedures
104
Figure 89
Removing the Slot Cover from the 2U PCIe Cage
18.
Remove the originally attached bracket from the smart array P212 controller board (for removing
methods of the originally attached bracket, please refer to the Figure 73 in this document).
19.
Install the low-profile vented bracket on the smart array P212 controller board (for installation
methods of the low-profile vented bracket, please refer to the Figure 74 in this document).
There are two types of vented brackets for the smart array P212 controller board: low-profile
and full-height. The low-profile vented bracket is for the smart array P212 controller board to be
installed on the low-profile riser card connector. The full-height vented bracket is for smart array
P212 controller board installed on the full-height riser card connector.
In this document we install the low-profile vented bracket for P212 as example since the primary
location for P212 on the riser card should always be the lowest connector (the low-profile
connector).
However, the following installation methods of the full-height vented bracket can be taken as
reference when you install P212 installed on the full-height riser card connector:
a.
Insert the smart array P212 controller board to the matching slot on the full-height vented
bracket. Make sure the smart array P212 controller board is aligned to the full-height vented
bracket by the 2 screw holes.
b.
Install the 2 screws to install the full-height vented bracket to smart array P212 controller
board.