HP ProLiant DL170e HP ProLiant DL170e G6 Server Maintenance and Service Guide - Page 120

Route the Right Exit and U Type Mini SAS to Mini SAS cables through the hole of the 2U PCIe

Get HP ProLiant DL170e - G6 Server PDF manuals and user guides View all HP ProLiant DL170e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 120 highlights

b. Install the 2 screws to install the full-height vented bracket to the smart array P410 controller board. Figure 116 Installing the Full-Height Vented Bracket to the Smart Array P410 Controller Board 13. Install the Right Exit and U Type Mini SAS to Mini SAS cables to the smart array P410 controller board as shown in Figure 110. 14. Align and install the smart array P410 controller board with its matching connector on the 2U riser card. 15. Install the screw to secure the smart array P410 controller board to the 2U PCIe cage. 16. Route the Right Exit and U Type Mini SAS to Mini SAS cables through the hole of the 2U PCIe cage as shown in figure below. Figure 117 Installing the Smart Array P410 Controller Board to a 2U PCIe Cage 17. Align one end of the card holder bracket into the slot of the 2U PCIe cage. 18. Route the card holder bracket down to attach it. Make sure that the stand off on the PCIe cage is aligned to the slot on the card holder bracket. 19. Tighten the thumbscrew to secure the card holder bracket to the 2U PCIe cage. Removal and replacement procedures 120

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
Removal and replacement procedures
120
b.
Install the 2 screws to install the full-height vented bracket to the smart array P410 controller
board.
Figure 116
Installing the Full-Height Vented Bracket to the Smart Array P410 Controller Board
13.
Install the Right Exit and U Type Mini SAS to Mini SAS cables to the smart array P410 controller
board as shown in Figure 110.
14.
Align and install the smart array P410 controller board with its matching connector on the 2U
riser card.
15.
Install the screw to secure the smart array P410 controller board to the 2U PCIe cage.
16.
Route the Right Exit and U Type Mini SAS to Mini SAS cables through the hole of the 2U PCIe
cage as shown in figure below.
Figure 117
Installing the Smart Array P410 Controller Board to a 2U PCIe Cage
17.
Align one end of the card holder bracket into the slot of the 2U PCIe cage.
18.
Route the card holder bracket down to attach it. Make sure that the stand off on the PCIe cage is
aligned to the slot on the card holder bracket.
19.
Tighten the thumbscrew to secure the card holder bracket to the 2U PCIe cage.