HP ProLiant DL170e HP ProLiant DL170e G6 Server Maintenance and Service Guide - Page 143

Node blank, Removal and replacement procedures, Reinstalling the 2U System Board Assembly

Get HP ProLiant DL170e - G6 Server PDF manuals and user guides View all HP ProLiant DL170e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 143 highlights

Figure 156 Reinstalling the 2U System Board Assembly 8. Route the handle of the 2U system board tray upwards until it snaps into place and locks the retaining latch. Figure 157 Locking the Retaining Latch of the 2U System Board Tray Node blank The server node blank should be installed when a node bay in the server is not populated with a node, so as to prevent improper cooling and thermal shutdown. WARNING: Failure to install a node blank wherever a node is removed from the server could result in the server shutting down. The following replacement procedures of the node blank use the 1U node as examples. To remove the node blank: 1. Press the locking latch on the node blank to release the node blank from the server. Removal and replacement procedures 143

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
Removal and replacement procedures
143
Figure 156
Reinstalling the 2U System Board Assembly
8.
Route the handle of the 2U system board tray upwards until it snaps into place and locks the
retaining latch.
Figure 157
Locking the Retaining Latch of the 2U System Board Tray
Node blank
The server node blank should be installed when a node bay in the server is not populated with a node,
so as to prevent improper cooling and thermal shutdown.
WARNING:
Failure to install a node blank wherever a node is removed from the server could result
in the server shutting down.
The following replacement procedures of the node blank use the 1U node as examples.
To remove the node blank:
1.
Press the locking latch on the node blank to release the node blank from the server.