IBM 86884RX Maintenance Manual - Page 121

Completing, installation, Closing, cover, Connecting, cables

Get IBM 86884RX - Eserver xSeries 450 PDF manuals and user guides View all IBM 86884RX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

6. Install fans 3 and 4 in the server (see "Replacing fan 3 or 4" on page 108 for details). 7. Close the server cover, and connect the cables. 8. Turn on the server. 9. Start the Configuration/Setup Utility program, and set configuration parameters. v Set the system date and time. v Set the power-on password. v Reconfigure your server. Completing the installation To complete your installation, close the server cover, reconnect all cables that you disconnected earlier and, for certain options, run the Configuration/Setup Utility program. Follow the instructions in this section. Attention: For proper cooling and airflow, close the server cover before or shortly after turning on the server. Operating the server for extended periods of time (over 15 minutes) with the server cover open might damage server components. Closing the cover Close the cover by first closing the right side; then, close the left side and press down to latch the two halves of the cover in place. NOTE: FOR PROPER FRONT OF BOX AIRFLOW, NOTE: FOR PROPER AIRFLOW, FRONT OF BOX REPLACE FAN WITHIN 2 MINUTES REPLACE FAN WITHIN 2 MINUTES Connecting the cables Notes: 1. You must turn off the server before connecting any cables to or disconnecting any cables from the server. 2. See the documentation that comes with your external options for additional cabling instructions. It might be easier for you to route any cables before you connect the devices to the server. Chapter 4. Installing options 111

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
6.
Install
fans
3
and
4
in
the
server
(see
“Replacing
fan
3
or
4”
on
page
108
for
details).
7.
Close
the
server
cover,
and
connect
the
cables.
8.
Turn
on
the
server.
9.
Start
the
Configuration/Setup
Utility
program,
and
set
configuration
parameters.
v
Set
the
system
date
and
time.
v
Set
the
power-on
password.
v
Reconfigure
your
server.
Completing
the
installation
To
complete
your
installation,
close
the
server
cover,
reconnect
all
cables
that
you
disconnected
earlier
and,
for
certain
options,
run
the
Configuration/Setup
Utility
program.
Follow
the
instructions
in
this
section.
Attention:
For
proper
cooling
and
airflow,
close
the
server
cover
before
or
shortly
after
turning
on
the
server.
Operating
the
server
for
extended
periods
of
time
(over
15
minutes)
with
the
server
cover
open
might
damage
server
components.
Closing
the
cover
Close
the
cover
by
first
closing
the
right
side;
then,
close
the
left
side
and
press
down
to
latch
the
two
halves
of
the
cover
in
place.
NOTE:
FOR PROPER AIRFLOW, REPLACE FAN WITHIN 2 MINUTES
FRONT OF BOX
NOTE:
FOR PROPER AIRFLOW, REPLACE FAN WITHIN 2 MINUTES
FRONT OF BOX
Connecting
the
cables
Notes:
1.
You
must
turn
off
the
server
before
connecting
any
cables
to
or
disconnecting
any
cables
from
the
server.
2.
See
the
documentation
that
comes
with
your
external
options
for
additional
cabling
instructions.
It
might
be
easier
for
you
to
route
any
cables
before
you
connect
the
devices
to
the
server.
Chapter
4.
Installing
options
111