Intel SE7501HG2 Product Guide - Page 41

Attaching the Heat Sink and Retention Clip, retention clip while sliding it to over.

Get Intel SE7501HG2 PDF manuals and user guides View all Intel SE7501HG2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

8. Align the heat sink over the processor and set it into place. If your heat sink has a flat end on it, as shown in the figure below, the flat end must point toward the rear of the chassis. 9. Position the retention clips over the plastic tabs at the center of the retention mechanism. Note that the slot in the clip provides room for side-to-side motion. Push down on the top of each retention clip while sliding it to over. (Figure 12, 1). 10. Engage each end of the retention clips over the plastic tabs at the sides of the retention mechanism (Figure 12, 2). 11. Press downward on the ends of the retention clips to lock them into place over the plastic tabs (Figure 12, 3 and 4). ✏ NOTE Make sure the center tab engages in the heat sink base. A C B C E 1 3 D 2 4 TP00099 Figure 12. Attaching the Heat Sink and Retention Clip Installations and Upgrades 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Installations and Upgrades
41
8.
Align the heat sink over the processor and set it into place.
If your heat sink has a flat end on it,
as shown in the figure below, the flat end must point toward the rear of the chassis.
9.
Position the retention clips over the plastic tabs at the center of the retention mechanism.
Note
that the slot in the clip provides room for side-to-side motion.
Push down on the top of each
retention clip while sliding it to over.
(Figure 12, 1).
10. Engage each end of the retention clips over the plastic tabs at the sides of the retention
mechanism (Figure 12, 2).
11. Press downward on the ends of the retention clips to lock them into place over the plastic tabs
(Figure 12, 3 and 4).
NOTE
Make sure the center tab engages in the heat sink base.
TP00099
A
B
C
C
D
E
1
2
3
4
Figure 12.
Attaching the Heat Sink and Retention Clip