Panasonic AW-UE100 Operating Instructions - Page 107
Bar [Camera, Colorbar], OSD Mix/Crop Marker, Video Sampling [4:2:2/10bit, 4:2:0/8bit], 3G SDI [Off,
View all Panasonic AW-UE100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 107 highlights
Web screen configurations (continued) HDMI Make the settings for output from the HDMI connector. Format Set the output format. The following format settings are possible depending on the [Format] setting in the [System] screen. Frequency System Format Format (HDMI) 59.94Hz 2160/59.94p 2160/29.97p 2160/59.94p *1 1080/59.94p *2 2160/29.97p *1 1080/29.97p 1080/59.94p 1080/59.94p 1080/59.94i 1080/59.94i 1080/29.97p 1080/29.97p 1080/29.97PsF 1080/29.97p 1080/23.98p(59.94i) *3 720/59.94p 1080/23.98p(59.94p) *4 720/59.94p 50Hz 2160/50p 2160/25p 2160/50p *1 1080/50p *5 2160/25p *1 1080/25p 1080/50p 1080/50p 1080/50i 1080/50i 1080/25p 1080/25p 1080/25PsF 1080/25p 720/50p 720/50p 24Hz 2160/24p 2160/24p *1 1080/24p 1080/24p 1080/24p 23.98Hz 2160/23.98p 2160/23.98p *1 1080/23.98p 1080/23.98p 1080/23.98p 1080/23.98PsF 1080/23.98p *1 Cannot be selected when [Crop Mode] is [Crop(1080)] or [Crop(720)]. *2 When [Crop Mode] is [Crop(720)], output is 720/59.94p. *3 It denotes "1080/23.98p over 59.94i". *4 It denotes "1080/23.98p over 59.94p". *5 When [Crop Mode] is [Crop(720)], output is 720/50p. Factory settings: 2160/59.94p (AW‑UE100WP/AW‑UE100KP/ AW‑UE100WPC/AW‑UE100KPC) 2160/50p (AW‑UE100WE/AW‑UE100KE/ AW‑UE100WED/AW‑UE100KED) Video Sampling [4:2:2/10bit, 4:2:0/8bit] When [Format] in [HDMI] is [2160/59.94p] or [2160/50p], select the video sampling output from the HDMI connector. 4:2:2/10bit Output in 4:2:2/10bit mode. 4:2:0/8bit Output in 4:2:0/8bit mode. Factory settings: 4:2:2/10bit • When [Format] in [HDMI] is other than [2160/59.94p] or [2160/50p], [Video Sampling] cannot be changed and is fixed at [4:2:2/10bit]. Bar [Camera, Colorbar] Switch between camera images and color bars. Camera Camera images Colorbar Color bar Factory settings: Camera Color Bar Type [Type1, Type2] Select the type of color bar to display. Type1: Type2: This is only enabled when [Bar] is set to [Colorbar]. Factory settings: Type2 Tone [Off, Low, Normal] Make the settings for the test tone signal (1 kHz) output while the color bar is displayed. Off Test tone is not output. Low Test tone is output at low volume. Normal Test tone is output at normal volume. This is only enabled when [Bar] is set to [Colorbar]. Factory settings: Normal OSD Mix/Crop Marker Selects whether to turn Off/On display of camera menu, status and crop frame. 12G SDI [Off, On*] Selects whether to turn this Off/On for images output from 12G SDI OUT connector. 3G SDI [Off, On*] Selects whether to turn this Off/On for images output from 3G SDI OUT connector. HDMI [Off, On*] Selects whether to turn this Off/On for images output from HDMI connector. NDI [Off, On*] Selects whether to turn this Off/On for images of NDI output from the LAN connector. IP/NDI|HX [Off, On*] Selects whether to turn this Off/On for images other than NDI images (H.264/H.265/JPEG/RTMP/SRT/NDI|HX) output from the LAN connector. Off The camera menus, statuses and crop frames are not displayed on the output pictures covered by the setting items listed above. On The camera menus, statuses and crop frames are displayed on the output pictures covered by the setting items listed above. * : Factory settings • When this is set to [Off], the camera menu can be displayed for about 1 minute after the unit is turned on. • It may not be possible to display the camera menus, statuses and crop frames even when this is set to [On]. For details, refer to "Exclusive conditions for [OSD Mix/Crop Marker]" (→ page 69). 107