Panasonic AW-UE100 Operating Instructions - Page 65

IP output, When performing video transmission via IP M-JPEG/H.264/H.265

Get Panasonic AW-UE100 PDF manuals and user guides View all Panasonic AW-UE100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Camera menu items (continued) zzIP output • When [IP] of [Tracking Data Output] on the [System 2/2] screen is set to [On], the tracking data for Pan/Tilt/Zoom or other information is synchronized with the Genlock signal and outputs UDP packets via IP. • Outputs simultaneously up to four clients (IP addresses) that have been specified on the designated web screen (→ page 137). • The tracking data is output in a format conforming to the free-d protocol. The output specification (mode, command type, advanced stored data) of this unit is equivalent to serial (RS-422) output. • When forwarding to more than one client, the timing of transmitting the UDP packet to the second and subsequent client will always be delayed relative to the Genlock signal. (Approximately 200 to 300 μs delay will occur for each client. The latency may be increased depending on the system status or the network environment of the unit.) • When [IP] is [On], video transmission via IP may be delayed or the video may suffer frame loss. We recommend setting [IP] to [Off] to avoid the delay or frame loss due to the video transmission via IP. • In the following cases, the tracking data output may be delayed or the value may not be updated. - When performing video transmission via IP (M-JPEG/H.264/H.265/ RTMP/RTMPS/NDI/NDI|HX/SRT) - When opening the web screen (live screen [Live] or the web setting screen [Setup]) - While viewing the OSD menu - While recalling the preset value during an ongoing preset recall - When executing AWB/ABB - When a red or a green tally signal input has been changed between Off and On - When deleting a preset memory - When an output image is flipped (turned upside down or left-right reversed) - After switching [Scene] - After switching [Iris Mode] - After switching [Super Gain] - After switching [White Balance Mode] - After switching each item of [Color TEMP. Setting] - After switching [Gamma Mode] - After switching [Matrix Type] - After switching [Focus Mode] - After switching [Zoom Mode] - After switching [Max Digital Zoom] - After switching [Digital Extender] - After switching [Fan] - After switching [OSD Mix/Crop Marker] - After switching [Tally] - After moving the crop frame of [UHD Crop] - After switching [Install Position] - After switching [Preset Speed Unit] - When executing [Initialize] of [Maintenance] 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
z
IP output
• When [IP] of [Tracking Data Output] on the [System 2/2] screen is
set to [On], the tracking data for Pan/Tilt/Zoom or other information is
synchronized with the Genlock signal and outputs UDP packets via IP.
• Outputs simultaneously up to four clients (IP addresses) that have
been specified on the designated web screen (→ page 137).
• The tracking data is output in a format conforming to the free-d
protocol. The output specification (mode, command type, advanced
stored data) of this unit is equivalent to serial (RS-422) output.
<NOTE>
• When forwarding to more than one client, the timing of transmitting
the UDP packet to the second and subsequent client will always be
delayed relative to the Genlock signal.
(Approximately 200 to 300 μs delay will occur for each client. The
latency may be increased depending on the system status or the
network environment of the unit.)
• When [IP] is [On], video transmission via IP may be delayed or the
video may suffer frame loss.
We recommend setting [IP] to [Off] to avoid the delay or frame loss
due to the video transmission via IP.
• In the following cases, the tracking data output may be delayed or the
value may not be updated.
- When performing video transmission via IP (M-JPEG/H.264/H.265/
RTMP/RTMPS/NDI/NDI|HX/SRT)
- When opening the web screen (live screen [Live] or the web setting
screen [Setup])
- While viewing the OSD menu
- While recalling the preset value during an ongoing preset recall
- When executing AWB/ABB
- When a red or a green tally signal input has been changed between
Off and On
- When deleting a preset memory
- When an output image is flipped (turned upside down or left-right
reversed)
- After switching [Scene]
- After switching [Iris Mode]
- After switching [Super Gain]
- After switching [White Balance Mode]
- After switching each item of [Color TEMP. Setting]
- After switching [Gamma Mode]
- After switching [Matrix Type]
- After switching [Focus Mode]
- After switching [Zoom Mode]
- After switching [Max Digital Zoom]
- After switching [Digital Extender]
- After switching [Fan]
- After switching [OSD Mix/Crop Marker]
- After switching [Tally]
- After moving the crop frame of [UHD Crop]
- After switching [Install Position]
- After switching [Preset Speed Unit]
- When executing [Initialize] of [Maintenance]
65
Camera menu items (continued)