Bernina Bernette 12 Instruction Manual - Page 118

Invisible zipper foot

Get Bernina Bernette 12 PDF manuals and user guides View all Bernina Bernette 12 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 118 highlights

10 12 15 EN Invisible zipper foot This foot is available as special accessory. This foot is used to insert invisible zippers so that they are covered by the seam, and thus hidden. Attach the invisible zipper foot to the machine. Adjust needle center position and straight stitch. Stitch length depends from the fabric. Adjust 1,0 - 3,0 mm. Place open zipper face - down on right side of fabric as shown in picture 1. Place the fabric edge at the 5/8 inch marking line on the needle plate surface. Place the zipper 1/4 inch below raw edge of garment. With right-hand groove of foot over coil, stitch zipper until the foot hits the slider. Remove the garment from the machine. To attach the other half of the zipper, place the fabric edge on the 5/8 inch marking line on the needle plate as shown in picture 2. With the left-hand groove of foot over coil, stitch zipper until the foot hits the slider. Close zipper. Fold the fabric that the zipper is on ride - hand side out of the way as shown in picture 2. Use a pin for fixing the fabric. Change to regular sewing foot and saw as close as possible with straight stitch against the zipper. At last carry out tie off with some forward and reverse stitches. Please note: No "S" marking is shown on the stitch length dial by model 10. 114 502020.75.24_021V4D0101_1010_IM_bernette 10 12 15_EN_DE_NL_FR

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
EN
±±´
10
12
15
This foot is available as special accessory.
This foot is used to insert invisible zippers so
that they are covered by the seam, and thus
hidden. Attach the invisible zipper
foot to the machine. Adjust needle center
position and straight stitch. Stitch length
depends from the fabric. Adjust 1,0 - 3,0
mm. Place open zipper face - down on right
side of fabric as shown in picture 1.
Place the fabric edge at the 5/8 inch marking
line on the needle plate surface. Place the
zipper 1/4 inch below raw edge of garment.
With right-hand groove of foot over coil,
stitch zipper until the foot hits the slider.
Remove the garment from the machine.
To attach the other half of the zipper, place
the fabric edge on the 5/8 inch marking line
on the needle plate as shown in picture 2.
With the left-hand groove of foot over coil,
stitch zipper until the foot hits the slider.
Close zipper. Fold the fabric that the zipper
is on ride - hand side out of the way as
shown in picture 2.
Use a pin for fixing the fabric. Change to
regular sewing foot and saw as close as
possible with straight stitch against the
zipper.
At last carry out tie off with some forward
and reverse stitches.
Please note:
No "S" marking is shown on the stitch length
dial by model 10.
Invisible zipper foot
502020.75.24_021V4D0101_1010_IM_bernette 10 12 15_EN_DE_NL_FR