HP StorageWorks 1606 Brocade Fabric Watch Administrator's Guide v6.3.0 (53-100 - Page 51

Fabric Watch activation, In this Interfaces for activating Fabric Watch

Get HP StorageWorks 1606 - Extension SAN Switch PDF manuals and user guides View all HP StorageWorks 1606 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Fabric Watch activation Chapter 5 In this chapter •Interfaces for activating Fabric Watch 27 Interfaces for activating Fabric Watch This section provides a brief overview of the available user interfaces for activating Fabric Watch. Further details about Fabric Watch operations for each interface are provided later in this guide. • Telnet session - Provides a command prompt where you can run Fabric OS commands to configure your switch monitoring settings. See "Activating Fabric Watch using a Telnet session" for instructions on how to activate Fabric Watch using a Telnet session. • Web Tools - Provides a graphical user interface that can be launched from an Internet browser, which allows you to launch a Fabric Watch window to configure switch monitoring settings. Using Web Tools, you can configure thresholds, alarms, and e-mail notifications. See "Activating Fabric Watch using Web Tools" on page 28 for instructions on how to activate Fabric Watch using Web Tools. • SNMP - Provides a receiver dedicated to monitoring the data center infracture; Brocade switches and directors enable monitoring of specific incidents and trigger an SNMP alert based on a user-defined threshold sending the alert to the dedicated SNMP trap receiver. Configuring SNMP threshold alerts for Fabric OS switches require using Web Toos to set up SNMP on the Fabric OS switch. See "Activating Fabric Watch using SNMP" on page 29 for instructions on how to set up SNMP. Activating Fabric Watch using a Telnet session 1. Connect to the switch and log in as admin. 2. Enter the following command, where switch represents the name or IP address of the switch: telnet switch After you enter this command, respond to the prompts for a username and password. 3. Enter the licenseShow command to determine if the Fabric Watch license is installed. switch:admin> licenseshow SedQyzdQbdTfeRzZ: Web license Zoning license bedR9dyyzzcfeSAW: Fabric license Scy9SbRQd9VdzATb: Fabric Watch license Fabric Watch Administrator's Guide 27 53-1001342-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
Fabric Watch Administrator’s Guide
27
53-1001342-01
Chapter
5
Fabric Watch activation
In this chapter
•
Interfaces for activating Fabric Watch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
Interfaces for activating Fabric Watch
This section provides a brief overview of the available user interfaces for activating Fabric Watch.
Further details about Fabric Watch operations for each interface are provided later in this guide.
•
Telnet session
- Provides a command prompt where you can run Fabric OS commands to
configure your switch monitoring settings. See
“Activating Fabric Watch using a Telnet session”
for instructions on how to activate Fabric Watch using a Telnet session.
•
Web Tools
- Provides a graphical user interface that can be launched from an Internet browser,
which allows you to launch a Fabric Watch window to configure switch monitoring settings.
Using Web Tools, you can configure thresholds, alarms, and e-mail notifications. See
“Activating Fabric Watch using Web Tools”
on page 28 for instructions on how to activate Fabric
Watch using Web Tools.
•
SNMP
- Provides a receiver dedicated to monitoring the data center infracture; Brocade
switches and directors enable monitoring of specific incidents and trigger an SNMP alert
based on a user-defined threshold sending the alert to the dedicated SNMP trap receiver.
Configuring SNMP threshold alerts for Fabric OS switches require using Web Toos to set up
SNMP on the Fabric OS switch. See
“Activating Fabric Watch using SNMP”
on page 29 for
instructions on how to set up SNMP.
Activating Fabric Watch using a Telnet session
1.
Connect to the switch and log in as admin.
2.
Enter the following command, where
switch
represents the name or IP address of the switch:
telnet
switch
After you enter this command, respond to the prompts for a username and password.
3.
Enter the
licenseShow
command to determine if the Fabric Watch license is installed.
switch:admin>
licenseshow
SedQyzdQbdTfeRzZ:
Web license
Zoning license
bedR9dyyzzcfeSAW:
Fabric license
Scy9SbRQd9VdzATb:
Fabric Watch license