Epson FX-2180 User Manual - Page 130

Changing default settings, Auto CR carriage return, IBM character table - enter language

Get Epson FX-2180 - Impact Printer PDF manuals and user guides View all Epson FX-2180 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 130 highlights

Auto CR (carriage return) This setting is available only in IBM 2381 Plus emulation mode. When you select On, each line feed (LF) code or ESC J code received by the printer is accompanied by a carriage return code. This moves the print position to the beginning of the next line. If the printer adds an extra line after every carriage return, select Off. IBM character table This setting is available only in IBM 2381 Plus emulation mode. When you select Table 1, hex codes 00 to 1FH and 80H to 9FH of the character tables are used for the control codes. When you select Table 2, hex codes 00 to 1FH are used for the control codes. See Appendix C for character samples. Changing default settings Follow the steps below to enter the default-setting mode and change the printer's default settings. Note: R To print the language selection and default-setting mode instructions, you need three sheets of A4- or letter-size single-sheet paper or three pages of continuous paper that is at least 279 mm (11 inches) long and 210 mm (8.27 inches) wide. See Chapter 2 for instructions on loading continuous paper, or Chapter 3 for instructions on loading single sheets. R If you use single sheets, you need to load a new sheet of paper each time the printer ejects a printed sheet. 5-8 Changing Printer Settings From the Printer's Control Panel

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
Auto CR (carriage return)
This setting is available only in IBM 2381 Plus emulation mode.
When you select
On
, each line feed (LF) code or ESC J code
received by the printer is accompanied by a carriage return
code. This moves the print position to the beginning of the next
line. If the printer adds an extra line after every carriage return,
select
Off
.
IBM character table
This setting is available only in IBM 2381 Plus emulation mode.
When you select
Table 1
, hex codes 00 to 1FH and 80H to 9FH
of the character tables are used for the control codes. When you
select
Table 2
, hex codes 00 to 1FH are used for the control
codes. See Appendix C for character samples.
Changing default settings
Follow the steps below to enter the default-setting mode and
change the printer’s default settings.
Note:
R
To print the language selection and default-setting mode
instructions, you need three sheets of A4- or letter-size
single-sheet paper or three pages of continuous paper that is at
least 279 mm (11 inches) long and 210 mm (8.27 inches) wide.
See Chapter 2 for instructions on loading continuous paper, or
Chapter 3 for instructions on loading single sheets.
R
If you use single sheets, you need to load a new sheet of paper
each time the printer ejects a printed sheet.
5-8
Changing Printer Settings From the Printer’s Control Panel