HP 6125XLG R2306-HP 6125XLG Blade Switch IP Multicast Command Reference - Page 146

mld static-group

Get HP 6125XLG PDF manuals and user guides View all HP 6125XLG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 146 highlights

Syntax mld group-policy acl6-number [ version-number ] undo mld group-policy Default No IPv6 multicast group filter is configured on an interface, and a host can join any IPv6 multicast group. Views Interface view Predefined user roles network-admin Parameters acl6-number: Specifies an IPv6 basic or advanced ACL by its number, in the range of 2000 to 3999. A host can join only the IPv6 multicast groups that match the permit statement in the ACL. The source addresses in the basic IPv6 rule are the IPv6 multicast group addresses specified in MLD reports. The source and destination addresses specified in the IPv6 advanced ACL rule are IPv6 multicast source addresses and multicast group addresses specified in MLD reports. The system assumes that 0::0 is the multicast source address of an MLDv1 report or an MLDv2 IS_EX and TO_EX report that does not carry an IPv6 multicast source address. version-number: Specifies an MLD version number, 1 or 2. By default, the configured group filter is effective for both MLDv1 reports and MLDv2 reports. Usage guidelines If you configure the interface as a static member interface for an IPv6 multicast group or an IPv6 multicast source and group, this configuration has no effect on the IPv6 multicast group or the IPv6 multicast source and group. Examples # Configure an IPv6 ACL so that hosts on VLAN-interface 100 can join the IPv6 multicast group FF03::101 only. system-view [Sysname] acl ipv6 number 2005 [Sysname-acl6-basic-2005] rule permit source ff03::101 128 [Sysname-acl6-basic-2005] quit [Sysname] interface vlan-interface 100 [Sysname-Vlan-interface100] mld group-policy 2005 mld static-group Use mld static-group to configure an interface as a static member of the specified IPv6 multicast group or the specified IPv6 multicast source and group. Use undo mld static-group to restore the default. Syntax mld static-group ipv6-group-address [ source ipv6-source-address ] undo mld static-group { all | ipv6-group-address [ source ipv6-source-address ] } 140

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
140
Syntax
mld group-policy
acl6-number
[
version-number
]
undo mld group-policy
Default
No IPv6 multicast group filter is configured on an interface, and a host can join any IPv6 multicast group.
Views
Interface view
Predefined user roles
network-admin
Parameters
acl6-number
: Specifies an IPv6 basic or advanced ACL by its number, in the range of 2000 to 3999. A
host can join only the IPv6 multicast groups that match the
permit
statement in the ACL. The source
addresses in the basic IPv6 rule are the IPv6 multicast group addresses specified in MLD reports. The
source and destination addresses specified in the IPv6 advanced ACL rule are IPv6 multicast source
addresses and multicast group addresses specified in MLD reports. The system assumes that 0::0 is the
multicast source address of an MLDv1 report or an MLDv2 IS_EX and TO_EX report that does not carry
an IPv6 multicast source address.
version-number
: Specifies an MLD version number, 1 or 2. By default, the configured group filter is
effective for both MLDv1 reports and MLDv2 reports.
Usage guidelines
If you configure the interface as a static member interface for an IPv6 multicast group or an IPv6 multicast
source and group, this configuration has no effect on the IPv6 multicast group or the IPv6 multicast source
and group.
Examples
# Configure an IPv6 ACL so that hosts on VLAN-interface 100 can join the IPv6 multicast group
FF03::101 only.
<Sysname> system-view
[Sysname] acl ipv6 number 2005
[Sysname-acl6-basic-2005] rule permit source ff03::101 128
[Sysname-acl6-basic-2005] quit
[Sysname] interface vlan-interface 100
[Sysname-Vlan-interface100] mld group-policy 2005
mld static-group
Use
mld static-group
to configure an interface as a static member of the specified IPv6 multicast group
or the specified IPv6 multicast source and group.
Use
undo mld static-group
to restore the default.
Syntax
mld static-group
ipv6-group-address
[
source
ipv6-source-address
]
undo mld static-group
{
all
|
ipv6-group-address
[
source
ipv6-source-address
] }