HP 6125XLG R2306-HP 6125XLG Blade Switch IP Multicast Command Reference - Page 44

ip rpf-route-static, Syntax, Default, Views, Predefined user roles, Parameters, Usage guidelines

Get HP 6125XLG PDF manuals and user guides View all HP 6125XLG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

ip rpf-route-static Use ip rpf-route-static to configure a static multicast route. Use undo ip rpf-route-static to delete a specific static multicast route. Syntax ip rpf-route-static source-address { mask-length | mask } { rpf-nbr-address | interface-type interface-number } [ preference preference ] undo ip rpf-route-static source-address { mask-length | mask } { rpf-nbr-address | interface-type interface-number } Default No static multicast route exists. Views System view Predefined user roles network-admin Parameters source-address: Specifies a multicast source address. mask-length: Specifies the address mask length, in the range of 0 to 32. mask: Specifies the mask. rpf-nbr-address: Specifies an RPF neighbor by its IP address. interface-type interface-number: Specifies an interface by its type and number. The interface connects the RPF neighbor. preference: Specifies a route preference, in the range of 1 to 255. The default value is 1. Usage guidelines In the same multicast source address range, you can configure up to 16 RPF neighbors. When you configure an RPF neighbor, you can specify the type and number of the interface only for the point-to-point interface. You can also specify the IP address for the interface that is not a point-to-point one, such as a loopback interface or VLAN interface. Because outgoing interface iteration might fail, or the specified interface is not a point-to-point one or might be in down state, the configured static multicast route might not take effect. In addition, if multiple static multicast routes within the same multicast source address range are available, only the one with the highest priority can become active. Therefore, after you configure a static multicast route, use the display multicast routing-table static command to verify that the configured static multicast route has taken effect. The undo ip rpf-route-static command deletes a specific static multicast route, and the delete ip rpf-route-static command deletes all static multicast routes. Examples # Configure a static multicast route to the multicast source groups 10.1.1.1/24, and specify a router with the IP address of 192.168.1.23 as its RPF neighbor. system-view [Sysname] ip rpf-route-static 10.1.1.1 24 192.168.1.23 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
37
ip rpf-route-static
Use
ip rpf-route-static
to configure a static multicast route.
Use
undo ip rpf-route-static
to delete a specific static multicast route.
Syntax
ip rpf-route-static
source-address
{
mask-length
|
mask
} {
rpf-nbr-address
|
interface-type
interface-number
} [
preference
preference
]
undo ip rpf-route-static
source-address
{
mask-length
|
mask
} {
rpf-nbr-address
|
interface-type
interface-number
}
Default
No static multicast route exists.
Views
System view
Predefined user roles
network-admin
Parameters
source-address:
Specifies a multicast source address.
mask-length
: Specifies the address mask length, in the range of 0 to 32.
mask
: Specifies the mask.
rpf-nbr-address
: Specifies an RPF neighbor by its IP address.
interface-type interface-number
: Specifies an interface by its type and number. The interface connects the
RPF neighbor.
preference
: Specifies a route preference, in the range of 1 to 255. The default value is 1.
Usage guidelines
In the same multicast source address range, you can configure up to 16 RPF neighbors.
When you configure an RPF neighbor, you can specify the type and number of the interface only for the
point-to-point interface. You can also specify the IP address for the interface that is not a point-to-point
one, such as a loopback interface or VLAN interface.
Because outgoing interface iteration might fail, or the specified interface is not a point-to-point one or
might be in down state, the configured static multicast route might not take effect. In addition, if multiple
static multicast routes within the same multicast source address range are available, only the one with the
highest priority can become active. Therefore, after you configure a static multicast route, use the
display
multicast routing-table static
command to verify that the configured static multicast route has taken effect.
The
undo ip rpf-route-static
command deletes a specific static multicast route, and the
delete ip
rpf-route-static
command deletes all static multicast routes.
Examples
# Configure a static multicast route to the multicast source groups 10.1.1.1/24, and specify a router with
the IP address of 192.168.1.23 as its RPF neighbor.
<Sysname> system-view
[Sysname] ip rpf-route-static 10.1.1.1 24 192.168.1.23