HP 6125XLG R2306-HP 6125XLG Blade Switch IP Multicast Command Reference - Page 97

state-refresh-rate-limit (PIM view), Syntax, Default, Views, Predefined user roles, Parameters

Get HP 6125XLG PDF manuals and user guides View all HP 6125XLG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

state-refresh-rate-limit (PIM view) Use state-refresh-rate-limit to configure the time that the router waits before receiving a new state refresh message. Use undo state-refresh-rate-limit to restore the default. Syntax state-refresh-rate-limit time undo state-refresh-rate-limit Default The device waits 30 seconds before it receives a new state refresh message. Views PIM view Predefined user roles network-admin Parameters time: Specifies a time (in seconds) that the device waits before receiving a new refresh message, in the range of 1 to 65535. Examples # Configure the device to wait 45 seconds before it receives a new state refresh message. system-view [Sysname] pim [Sysname-pim] state-refresh-rate-limit 45 Related commands • pim state-refresh-capable • state-refresh-interval (PIM view) • state-refresh-ttl (PIM view) state-refresh-ttl (PIM view) Use state-refresh-ttl to set the TTL value of state refresh messages. Use undo state-refresh-ttl to restore the default. Syntax state-refresh-ttl ttl-value undo state-refresh-ttl Default The TTL value of state refresh messages is 255. Views PIM view 91

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
91
state-refresh-rate-limit (PIM view)
Use
state-refresh-rate-limit
to configure the time that the router waits before receiving a new state refresh
message.
Use
undo state-refresh-rate-limit
to restore the default.
Syntax
state-refresh-rate-limit
time
undo state-refresh-rate-limit
Default
The device waits 30 seconds before it receives a new state refresh message.
Views
PIM view
Predefined user roles
network-admin
Parameters
time
: Specifies a time (in seconds) that the device waits before receiving a new refresh message, in the
range of 1 to 65535.
Examples
# Configure the device to wait 45 seconds before it receives a new state refresh message.
<Sysname> system-view
[Sysname] pim
[Sysname-pim] state-refresh-rate-limit 45
Related commands
•
pim state-refresh-capable
•
state-refresh-interval
(PIM view)
•
state-refresh-ttl
(PIM view)
state-refresh-ttl (PIM view)
Use
state-refresh-ttl
to set the TTL value of state refresh messages.
Use
undo state-refresh-ttl
to restore the default.
Syntax
state-refresh-ttl
ttl-value
undo state-refresh-ttl
Default
The TTL value of state refresh messages is 255.
Views
PIM view