HP 6125XLG R2306-HP 6125XLG Blade Switch IP Multicast Command Reference - Page 96

state-refresh-interval (PIM view), Usage guidelines, Examples, Syntax, Default, Views

Get HP 6125XLG PDF manuals and user guides View all HP 6125XLG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

Usage guidelines CAUTION: If the device is an RP, disabling switchover to SPT might cause multicast traffic forwarding failures on the source-side DR. When disabling switchover to SPT, be sure you fully understand its impact on your network. The source field in an ACL specifies the multicast group range. If you specify a VPN instance in the ACL, the ACL does not take effect. The other optional parameters except the fragment keyword and the time-range keyword are ignored. Examples # Disable switchover to SPT on a receiver-side DR. system-view [Sysname] pim [Sysname-pim] spt-switch-threshold infinity state-refresh-interval (PIM view) Use state-refresh-interval to configure the interval for sending state refresh messages. Use undo state-refresh-interval to restore the default. Syntax state-refresh-interval interval undo state-refresh-interval Default The interval for sending state refresh messages is 60 seconds. Views PIM view Predefined user roles network-admin Parameters interval: Specifies the interval (in seconds) for sending state refresh messages, in the range of 1 to 255. Examples # Set the interval for sending state refresh messages to 70 seconds. system-view [Sysname] pim [Sysname-pim] state-refresh-interval 70 Related commands • pim state-refresh-capable • state-refresh-rate-limit (PIM view) • state-refresh-ttl (PIM view) 90

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
90
Usage guidelines
CAUTION:
If the device is an RP, disabling switchover to SPT might cause multicast traffic forwarding failures on the
source-side DR. When disabling switchover to SPT, be sure you fully understand its impact on your
network.
The source field in an ACL specifies the multicast group range. If you specify a VPN instance in the ACL,
the ACL does not take effect. The other optional parameters except the
fragment
keyword and the
time-range
keyword are ignored.
Examples
# Disable switchover to SPT on a receiver-side DR.
<Sysname> system-view
[Sysname] pim
[Sysname-pim] spt-switch-threshold infinity
state-refresh-interval (PIM view)
Use
state-refresh-interval
to configure the interval for sending state refresh messages.
Use
undo state-refresh-interval
to restore the default.
Syntax
state-refresh-interval
interval
undo state-refresh-interval
Default
The interval for sending state refresh messages is 60 seconds.
Views
PIM view
Predefined user roles
network-admin
Parameters
interval
: Specifies the interval (in seconds) for sending state refresh messages, in the range of 1 to 255.
Examples
# Set the interval for sending state refresh messages to 70 seconds.
<Sysname> system-view
[Sysname] pim
[Sysname-pim] state-refresh-interval 70
Related commands
•
pim state-refresh-capable
•
state-refresh-rate-limit
(PIM view)
•
state-refresh-ttl
(PIM view)