HP LH4r HP Netserver LC 2000 Installation Guide - Page 126

Floppy check, Disabled], Summary screen, Enabled], Quick Boot mode, Boot Device Priority, Hard Drive

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 126 highlights

Chapter 10 Configuring the HP NetServer 17. To use the Hardware Security menu under Security, use the help files provided with the selections. 18. Select the Esc key to exit this menu. 19. Use the right-arrow key to go to the Exit menu. 20. Choose Exit Saving Changes from the list of exit options, and then press Enter. A dialog appears and asks you to confirm your decision. 21. Choose Yes and then press the Enter key. Then the HP NetServer reboots. 22. To change one of the passwords at a later date, return to the Security menu and repeat Steps 2 through 7 above for one or both passwords. NOTE The HP NetServer allows you to reset the password by toggling a switch, position 6, in the Configuration Switch Block on the System board. Changing Internal Device Boot Priority You can change the boot priority of the HP NetServer's internal mass storage devices: the CD-ROM, the flexible disk drive (or other removable device), and hard drives connected to the HP NetServer's internal SCSI ports. 1. Select "Boot Settings" from the Configuration menu, using the down-arrow or up-arrow key, and press Enter. A Boot Settings screen appears, very similar to the one below. Floppy check: [Disabled] Summary screen: [Enabled] Quick Boot mode: ­Boot Device Priority [Enabled] ­Hard Drive Priority 2. Use the down-arrow key to move to the "Boot Device Priority" field. 118

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Chapter 10
Configuring the HP NetServer
118
17.
To use the Hardware Security menu under Security, use the help files
provided with the selections.
18.
Select the
Esc
key to exit this menu.
19.
Use the right-arrow key to go to the Exit menu.
20. Choose
Exit Saving Changes
from the list of exit options, and then press
Enter
.
A dialog appears and asks you to confirm your decision.
21. Choose
Yes
and then press the
Enter
key.
Then the HP NetServer reboots.
22.
To change one of the passwords at a later date, return to the Security menu
and repeat Steps 2 through 7 above for one or both passwords.
NOTE
The HP NetServer allows you to reset the password by toggling
a switch, position 6, in the Configuration Switch Block on the
System board.
Changing Internal Device Boot Priority
You can change the boot priority of the HP NetServer’s internal mass storage
devices: the CD-ROM, the flexible disk drive (or other removable device), and
hard drives connected to the HP NetServer’s internal SCSI ports.
1.
Select "Boot Settings" from the Configuration menu, using the down-arrow
or up-arrow key, and press
Enter
.
A Boot Settings screen appears, very similar to the one below.
Floppy check:
[Disabled]
Summary screen:
[Enabled]
Quick Boot mode:
[Enabled]
Boot Device Priority
Hard Drive Priority
2.
Use the down-arrow key to move to the "Boot Device Priority" field.