HP LH4r HP Netserver LC 2000 Installation Guide - Page 57

If the drive is unseated in the cage after closing the ejector handle, repeat

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Chapter 4 Installing Mass Storage Devices CAUTION Use caution when handling the drive to prevent damage to the fragile light pipes as you insert the drive. 5. Gently slide the drive module into the cage and stop when you feel resistance. See Figure 4-11. Figure 4-11. Inserting the Drive 6. Verify the pin behind the pivot end of the handle engages the hole in the edge of the cage. 7. Press the ejector handle in until you feel the latch click into place. Closing the ejector handle engages the drive with the electrical connector in the Hot Swap drive cage and seats the drive. 8. If the drive is unseated in the cage after closing the ejector handle, repeat this procedure from Steps 4 to 7. The handle was probably not pulled out far enough, and the locking latch failed to engage the Hot Swap mass storage cage. NOTE Closing the ejector handle engages the drive with the electrical connector in the Hot Swap mass storage cage and seats the drive. 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Chapter 4
Installing Mass Storage Devices
49
CAUTION
Use caution when handling the drive to prevent damage to the
fragile light pipes as you insert the drive.
5.
Gently slide the drive module into the cage and stop when you feel
resistance. See Figure 4-11.
Figure 4-11. Inserting the Drive
6.
Verify the pin behind the pivot end of the handle engages the hole in the
edge of the cage.
7.
Press the ejector handle in until you feel the latch click into place.
Closing the ejector handle engages the drive with the electrical connector
in the Hot Swap drive cage and seats the drive.
8.
If the drive is unseated in the cage after closing the ejector handle, repeat
this procedure from Steps 4 to 7.
The handle was probably not pulled out far enough, and the locking latch
failed to engage the Hot Swap mass storage cage.
NOTE
Closing the ejector handle engages the drive with the electrical
connector in the Hot Swap mass storage cage and seats the
drive.