HP LH4r HP Netserver LC 2000 Installation Guide - Page 146

: Incorrect System Configuration

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 146 highlights

Chapter 12 Troubleshooting To clear the system configuration on the System Board: 1. Turn off power to the HP NetServer, and unplug the power cord. 2. Remove the front bezel and left side cover (or top cover). Refer to Figures 12-1, 12-2, and the Technical Reference Label. 3. Move the configuration memory switch, switch 5 on the system board, to the "ON = Clear Config" position. 4. Plug in the power cord, and turn on power to the HP NetServer. The following message is displayed: Configuration has been cleared, set Clear Config switch to the OFF position before rebooting 5. Turn off power to the HP NetServer, and unplug the power cord. 6. Return switch 5 on the system board to the OFF position. 7. Replace the left side cover (or top cover), and the front bezel, and plug in the power cord. 8. Turn on power to the HP NetServer and the following error message may be displayed. 0012-34 : Incorrect System Configuration If the error message above is displayed, it is followed by the explanation message below. This is normal operation when clearing CMOS. The BIOS has detected a serious problem that prevents your PC from booting 9. Press the F2 key to run the Setup Utility. 10. Make any required configuration changes. 11. Press the F10 function key and answer "Yes" to save the configuration and exit the Setup Utility. 138

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Chapter 12
Troubleshooting
138
To clear the system configuration on the System Board:
1.
Turn off power to the HP NetServer, and unplug the power cord.
2.
Remove the front bezel and left side cover (or top cover).
Refer to Figures 12-1, 12-2, and the Technical Reference Label.
3.
Move the configuration memory switch, switch 5 on the system board, to
the "ON = Clear Config" position.
4.
Plug in the power cord, and turn on power to the HP NetServer.
The following message is displayed:
Configuration has been cleared, set Clear
Config switch to the OFF position before
rebooting
5.
Turn off power to the HP NetServer, and unplug the power cord.
6.
Return switch 5 on the system board to the OFF position.
7.
Replace the left side cover (or top cover), and the front bezel, and plug in
the power cord.
8.
Turn on power to the HP NetServer and the following error message may
be displayed.
0012-34 : Incorrect System Configuration
If the error message above is displayed, it is followed by the explanation
message below. This is normal operation when clearing
CMOS.
The BIOS has detected a serious problem
that prevents your PC from booting
9.
Press the
F2
key to run the Setup Utility.
10.
Make any required configuration changes.
11.
Press the
F10
function key and answer "Yes" to save the configuration and
exit the Setup Utility.