HP LH4r HP Netserver LC 2000 Installation Guide - Page 58

Removing Hot Swap Hard Drives

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Chapter 4 Installing Mass Storage Devices Removing Hot Swap Hard Drives CAUTION You must remove the drive slowly to ensure the drive heads are parked prior to removal. Ensure you follow these instructions carefully to prevent handling damage, such as head slaps or head actuator unlocking. 1. To unlock the drive, push the locking latch in and then pull the ejector handle toward you. See Figures 4-10 and 4-12. 2. Gently pull the drive out about an inch to disengage the power connection. 3. Wait about 30 seconds for the drive to stop spinning and the drive heads to park. 4. Use your hand to support the bottom of the drive, while you slowly pull the drive straight out. Do not allow the drive to fall. 5. Place the drive in an electrostatic-protected container. Do not stack drives. Figure 4-12. Hot Swap Drive 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Chapter 4
Installing Mass Storage Devices
50
Removing Hot Swap Hard Drives
CAUTION
You must remove the drive slowly to ensure the drive heads
are parked prior to removal.
Ensure you follow these
instructions carefully to prevent handling damage, such as
head slaps or head actuator unlocking.
1.
To unlock the drive, push the locking latch in and then pull the ejector
handle toward you.
See Figures 4-10 and 4-12.
2.
Gently pull the drive out about an inch to disengage the power connection.
3.
Wait about 30 seconds for the drive to stop spinning and the drive heads to
park.
4.
Use your hand to support the bottom of the drive, while you slowly pull the
drive straight out.
Do not allow the drive to fall.
5.
Place the drive in an electrostatic-protected container.
Do not stack drives.
Figure 4-12.
Hot Swap Drive