HP LH4r HP Netserver LC 2000 Installation Guide - Page 91

See

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Chapter 8 Rack-Mounting the HP NetServer 1. Find the rack-mounting template. If your HP NetServer is still in its box, the template should be in the accessories tray that sits on top of the NetServer itself. 2. Hold the template alongside the outside face (front) of the left front rack columns. 3. Line up the bottom of the template with the lower line of the NetServer's location in the rack. The template covers a span of 5 EIA units, which is the height requirement of the HP NetServer. 4. Use the marking pen to mark the 2nd and 14th holes on both front columns, as shown on the template. See Figure 8-3. NOTE The two column adapters are mounted at the 2nd and 14th holes on the respective front column and provide the captive nuts for mounting the rack slides to the front columns at 7th and 9th holes from the bottom. If you don't have the template, Figure 8-3 shows the location on the front columns for the column adapters. Figure 8-2. Placing Rack Nuts on Rack Columns 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Chapter 8
Rack-Mounting the HP NetServer
83
1.
Find the rack-mounting template.
If your HP NetServer is still in its box, the template should be in the
accessories tray that sits on top of the NetServer itself.
2.
Hold the template alongside the outside face (front) of the left front rack
columns.
3.
Line up the bottom of the template with the lower line of the NetServer’s
location in the rack.
The template covers a span of 5 EIA units, which is the height requirement
of the HP NetServer.
4.
Use the marking pen to mark the 2nd and 14th holes on both front
columns, as shown on the template.
See Figure 8-3.
NOTE
The two column adapters are mounted at the 2nd and 14th
holes on the respective front column and provide the captive
nuts for mounting the rack slides to the front columns at 7th
and 9th holes from the bottom.
If you don’t have the template,
Figure 8-3 shows the location on the front columns for the
column adapters.
Figure 8-2. Placing Rack Nuts on Rack Columns