HP LH4r HP Netserver LC 2000 Installation Guide - Page 98

NetServer. See

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

Chapter 8 Rack-Mounting the HP NetServer Figure 8-9. Removing the Mounting Handles 10. Insert the flathead screws into the slides'holes at the rear and the panheads screws in the other four places to secure the chassis to the slides. 11. Use a T-15 Torx driver to remove the screws holding the handles to the NetServer. See Figure 8-9. 12. Take the handles off the NetServer and store the handles and screws in a convenient place. See Figure 8-9. The handles can be re-attached whenever you remove the NetServer from the rack. If moving the NetServer elsewhere, always package it with the handles attached. 13. Press in the release latches on each slide, and push the NetServer all the way into the rack. See Figure 8-10. The blue Slide Release buttons in the Bezel moldings on each side of chassis' front edge must click into the latches in the column adapters on the two front rack columns. 90

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Chapter 8
Rack-Mounting the HP NetServer
90
Figure 8-9. Removing the Mounting Handles
10.
Insert the flathead screws into the slides’ holes at the rear and the panheads
screws in the other four places to secure the chassis to the slides.
11.
Use a T-15 Torx driver to remove the screws holding the handles to the
NetServer. See Figure 8-9.
12.
Take the handles off the NetServer and store the handles and screws in a
convenient place. See Figure 8-9.
The handles can be re-attached whenever you remove the NetServer from
the rack. If moving the NetServer elsewhere, always package it with the
handles attached.
13.
Press in the release latches on each slide, and push the NetServer all the
way into the rack. See Figure 8-10.
The blue Slide Release buttons in the Bezel moldings on each side of
chassis’ front edge must click into the latches in the column adapters on the
two front rack columns.