HP LH4r HP Netserver LC 2000 Installation Guide - Page 97
See
 |
View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 97 highlights
Chapter 8 Rack-Mounting the HP NetServer Channel(2) Figure 8-8. Mounting the HP NetServer on the Slides 7. Move the slide members into the NetServer's channels until both slide members are underneath all four of the NetServer's handles. See Figures 8-8 and 8-9. The mounting tabs in the slides should be in position to fit into the openings in the chassis. See Figures 8-7 and 8-8. 8. Lower the NetServer onto the slide members. See Figure 8-9. The handles will temporarily support the NetServer on the slides. 9. Adjust the NetServer's position on the slide members to line up the mounting holes on each side (3 each) of the chassis with the screw holes in the slide members. 89
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92 -
93 -
94 -
95 -
96 -
97 -
98 -
99 -
100 -
101 -
102 -
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
 |
 |
Chapter 8
Rack-Mounting the HP NetServer
89
Channel(2)
Figure 8-8. Mounting the HP NetServer on the Slides
7.
Move the slide members into the NetServer’s channels until both slide
members are underneath all four of the NetServer's handles.
See Figures
8-8 and 8-9.
The mounting tabs in the slides should be in position to fit into the
openings in the chassis. See Figures 8-7 and 8-8.
8.
Lower the NetServer onto the slide members.
See Figure 8-9.
The handles will temporarily support the NetServer on the slides.
9.
Adjust the NetServer's position on the slide members to line up the
mounting holes on each side (3 each) of the chassis with the screw holes in
the slide members.