HP LH4r HP Netserver LC 2000 Installation Guide - Page 37

snap-in connectors at the top front of the chassis and two metal tabs, which

Page 37 highlights

Chapter 3 Opening and Closing the HP NetServer 3. Press the power switch on the HP NetServer's control panel when prompted by the operating system. Normally, this completes the power-down procedure. 4. Disconnect the power cord from its power source. 5. To remove the bezel, pull the top of the bezel forward until it unsnaps, then lift the entire bezel upward and away from the chassis. See Figure 3-6. The bezel connects to the front of the HP NetServer chassis with two snap-in connectors at the top front of the chassis and two metal tabs, which fit into two slots on the bottom front of the chassis. Figure 3-6. Removing the HP NetServer LC 2000 Bezel CAUTION To prevent damage to the covers, support the cover as you remove it from the HP NetServer. The NetServer's covers can be easily damaged. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194

Chapter 3
Opening and Closing the HP NetServer
29
3.
Press the power switch on the HP NetServer’s control panel when
prompted by the operating system.
Normally, this completes the power-down procedure.
4.
Disconnect the power cord from its power source.
5.
To remove the bezel, pull the top of the bezel forward until it unsnaps, then
lift the entire bezel upward and away from the chassis. See Figure 3-6.
The bezel connects to the front of the HP NetServer chassis with two
snap-in connectors at the top front of the chassis and two metal tabs, which
fit into two slots on the bottom front of the chassis.
Figure 3-6.
Removing the HP NetServer LC 2000 Bezel
CAUTION
To prevent damage to the covers, support the cover as you
remove it from the HP NetServer. The NetServer’s covers can
be easily damaged.