HP LH4r HP Netserver LC 2000 Installation Guide - Page 40

Removing the Pedestal

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Chapter 3 Opening and Closing the HP NetServer Removing the Pedestal The pedestal version of the HP NetServer LC 2000 mounts to an anti-tip pedestal, which can be easily removed, if necessary. 1. Perform Steps 1-4 in the previous section, "Removing Covers - Pedestal (LC 2000)." NOTE The front bezel is shown removed, but the bezel may remain on the chassis while removing the pedestal. 2. Disconnect all cables connected to the rear of the NetServer that would limit its rotation before continuing. 3. Turn the NetServer over onto its top and pull up on the two tabs as shown in Figure 3-9. Figure 3-9. Removing the Pedestal 4. Slide the pedestal to the rear of the NetServer as shown in Figure 3-9. 5. To re-install the pedestal, repeat Steps 1-3 and slide the pedestal forward onto the NetServer. 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Chapter 3
Opening and Closing the HP NetServer
32
Removing the Pedestal
The pedestal version of the HP NetServer LC 2000 mounts to an anti-tip pedestal,
which can be easily removed, if necessary.
1.
Perform Steps 1-4 in the previous section, "Removing Covers – Pedestal
(LC 2000)."
NOTE
The front bezel is shown removed, but the bezel may remain on
the chassis while removing the pedestal.
2.
Disconnect all cables connected to the rear of the NetServer that would
limit its rotation before continuing.
3.
Turn the NetServer over onto its top and pull up on the two tabs as shown
in Figure 3-9.
Figure 3-9. Removing the Pedestal
4.
Slide the pedestal to the rear of the NetServer as shown in Figure 3-9.
5.
To re-install the pedestal, repeat Steps 1-3 and slide the pedestal forward
onto the NetServer.