HP LH4r HP Netserver LC 2000 Installation Guide - Page 73

Installing Accessory Boards

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Chapter 6 Installing Additional Boards Open = Off Closed = On 2 Processor Speed (Bit 1) 3 Processor Speed (Bit 2) 4 Processor Speed (Bit 3) 5 Clear Configuration 6 Clear Password Shaded rectangle represents the position of slide switch. 8 FSB Speed (133/100 MHz) Rear of HP NetServer Figure 6-2. Configuration Switch Block Installing Accessory Boards Use this procedure to install all accessory boards. 1. Read the documentation included with each board and follow any special instructions provided. CAUTION To prevent a system crash, never remove or insert a PCI board from or into a slot with the NetServer powered on. Always turn power off to the NetServer before performing any installation or removal operations. 2. Log off all users and back-up all files. 3. Follow the instructions in the respective NOS (network operating system) documentation to gracefully shut down all networking software and applications. 4. Press the power button on the HP NetServer's control panel when prompted by the operating system. Normally, this completes the shutdown procedure. NOTE The power supplies will continue to provide standby current to the NetServer until the power cable is disconnected. 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Chapter 6
Installing Additional Boards
65
Shaded rectangle
represents the
position of slide
switch.
2
Processor Speed (Bit 1)
3
Processor Speed (Bit 2)
4
Processor Speed (Bit 3)
5
Clear Configuration
6
Clear Password
8
FSB Speed (133/100 MHz)
Open = Off
Closed = On
Rear of HP NetServer
Figure 6-2. Configuration Switch Block
Installing Accessory Boards
Use this procedure to install all accessory boards.
1.
Read the documentation included with each board and follow any special
instructions provided.
CAUTION
To prevent a system crash, never remove or insert a PCI board
from or into a slot with the NetServer powered on. Always
turn power off to the NetServer before performing any
installation or removal operations.
2.
Log off all users and back-up all files.
3.
Follow the instructions in the respective NOS (network operating system)
documentation to gracefully shut down all networking software and
applications.
4.
Press the power button on the HP NetServer’s control panel when
prompted by the operating system.
Normally, this completes the shutdown procedure.
NOTE
The power supplies will continue to provide standby current to
the NetServer until the power cable is disconnected.