HP LH4r HP Netserver LC 2000 Installation Guide - Page 31

See Rack-Mounting the HP NetServer

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Chapter 3 Opening and Closing the HP NetServer 3. Press the power switch on the HP NetServer's control panel when prompted by the operating system. Normally, this completes the power down procedure. 4. Disconnect the power cord or cords from the power source. NOTE The power supplies will continue to provide standby current to the NetServer until the power cable is disconnected. 5. At the front of the HP NetServer, extend the anti-tip foot from under the front of the rack. See Chapter 8, "Rack-Mounting the HP NetServer," later in this manual. Leveler Foot (4) Anti-Tip Foot Extended Figure 3-1. Extend the Rack's Anti-Tip Foot WARNING This anti-tip device must be extended to prevent the rack and HP NetServer from tipping over, which could damage the NetServer and injure people. 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Chapter 3
Opening and Closing the HP NetServer
23
3.
Press the power switch on the HP NetServer’s control panel when
prompted by the operating system.
Normally, this completes the power down procedure.
4.
Disconnect the power cord or cords from the power source.
NOTE
The power supplies will continue to provide standby current to
the NetServer until the power cable is disconnected.
5.
At the front of the HP NetServer, extend the anti-tip foot from under the
front of the rack.
See Chapter 8, "Rack-Mounting the HP NetServer,"
later in this manual.
Leveler
Foot (4)
Anti-Tip
Foot Extended
Figure 3-1. Extend the Rack’s Anti-Tip Foot
WARNING
This anti-tip device must be extended to prevent the rack and
HP NetServer from tipping over, which could damage the
NetServer and injure people.