HP LH4r HP Netserver LC 2000 Installation Guide - Page 68

Refer to Controls, Ports, and Indicators.

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 68 highlights

Chapter 5 Installing Additional Memory Figure 5-4. Removing a DIMM Module 6. Repeat Steps 2 through 5 to remove any additional desired DIMMs on the system board. NOTE Ensure the retaining clips on the DIMM slots for each DIMM are closed before replacing the cover onto the HP NetServer. An error will be displayed if all DIMMs are removed. 7. If all desired DIMMs have been removed, replace the cover. Refer to Chapter 3, "Opening and Closing the HP NetServer." 8. If the NetServer is a rack installation, return the chassis into the rack. Refer to Chapter 3, "Opening and Closing the HP NetServer." 9. Re-install the bezel onto the front of the HP NetServer. Refer to Chapter 3, "Opening and Closing the HP NetServer." 10. Reconnect the power cord(s). 11. Power on the HP NetServer according to the respective NOS power-up instructions. Refer to Chapter 2, "Controls, Ports, and Indicators." 12. Return the HP NetServer to normal operation. 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Chapter 5
Installing Additional Memory
60
Figure 5-4. Removing a DIMM Module
6.
Repeat Steps 2 through 5 to remove any additional desired DIMMs on the
system board.
NOTE
Ensure the
retaining clips on the DIMM slots for each DIMM
are closed before replacing the cover onto the HP NetServer.
An error will be displayed if all DIMMs are removed.
7.
If all desired DIMMs have been removed, replace the cover.
Refer to Chapter 3, "Opening and Closing the HP NetServer."
8.
If the NetServer is a rack installation, return the chassis into the rack.
Refer to Chapter 3, "Opening and Closing the HP NetServer."
9.
Re-install the bezel onto the front of the HP NetServer.
Refer to Chapter 3, "Opening and Closing the HP NetServer."
10.
Reconnect the power cord(s).
11.
Power on the HP NetServer according to the respective NOS power-up
instructions.
Refer to Chapter 2, "Controls, Ports, and Indicators."
12.
Return the HP NetServer to normal operation.