HP LH4r HP Netserver LC 2000 Installation Guide - Page 167

Hinge Pins 3, Blue Tab, Slide Securing Screws2

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 167 highlights

Chapter 13 Alternative Rack Mounting 10. Plug the NetServer's power cable and all available data cables into the back of the NetServer. Attaching the Front Bezel The front bezel attaches to the HP NetServer by a hinge on the left and a catch on the right. The hinge has three spring-loaded hinge pins to secure the bezel. The bezel is held in place on the right with a catch allowing the bezel to swing open when pulled from the right. The chassis is shipped with the bezel hinge and latch in place. The column adapters are the only items requiring installation on the rack, which is done before mounting the rack slides. 1. Position the Bezel in front of the HP NetServer LC 2000r as shown in Figure 13-12. The hinge pins must be pushed down with the blue Bezel Release tab shown in Figure 13-12 to engage the hinge pins. When the Blue Tab is released, the spring loaded hinge pins move up to grasp the bezel holding it in place. The open bezel is then swung closed on the right to engage the catch. See Figure 13-13. Blue Tab Slide Securing Screws(2) Hinge Pins (3) Figure 13-12. Hinge Pins and Blue Bezel Release Tab 159

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Chapter 13
Alternative Rack Mounting
159
10.
Plug the NetServer’s power cable and all available data cables into the back
of the NetServer.
Attaching the Front Bezel
The front bezel attaches to the HP NetServer by a hinge on the left and a catch on
the right. The hinge has three spring-loaded hinge pins to secure the bezel. The
bezel is held in place on the right with a catch allowing the bezel to swing open
when pulled from the right. The chassis is shipped with the bezel hinge and latch
in place. The column adapters are the only items requiring installation on the rack,
which is done before mounting the rack slides.
1.
Position the Bezel in front of the HP NetServer LC 2000r as shown in
Figure 13-12.
The hinge pins must be pushed down with the blue Bezel Release tab
shown in Figure 13-12 to engage the hinge pins. When the Blue Tab is
released, the spring loaded hinge pins move up to grasp the bezel holding it
in place. The open bezel is then swung closed on the right to engage the
catch. See Figure 13-13.
Hinge Pins (3)
Blue Tab
Slide Securing Screws(2)
Figure 13-12. Hinge Pins and Blue Bezel Release Tab