HP LH4r HP Netserver LC 2000 Installation Guide - Page 75
Do not bend the PCI board to install it into the slot. If
 |
View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 75 highlights
Chapter 6 Installing Additional Boards 8. Remove the slot cover from the NetServer's rear panel, before installing the new board into the slot, as shown in Figure 6-3. 2. Lift Latch 3. Remove Slot Cover 1. Open Tab NOTE Figure 6-3. Removing the Slot Cover Each PCI slot must have a slot cover or PCI board in the slot. Ensure all unused slots have slot covers in place. CAUTION Do not bend the PCI board to install it into the slot. If a full-length PCI board has a handle on the end of the board that prevents its installation, remove the handle before installing the board. 67
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70 -
71 -
72 -
73 -
74 -
75 -
76 -
77 -
78 -
79 -
80 -
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
 |
 |
Chapter 6
Installing Additional Boards
67
8.
Remove the slot cover from the NetServer’s rear panel, before installing
the new board into the slot, as shown in Figure 6-3.
1. Open Tab
2. Lift Latch
3. Remove Slot Cover
Figure 6-3. Removing the Slot Cover
NOTE
Each PCI slot must have a slot cover or PCI board in the slot.
Ensure all unused slots have slot covers in place.
CAUTION
Do not bend the PCI board to install it into the slot. If a
full-length PCI board has a handle on the end of the board that
prevents its installation, remove the handle before installing
the board.