HP 6125G HP 6125G & 6125G/XG Blade Switches Layer 3 - IP Services Conf - Page 152

Enable IPv6., Create service loopback group 1 to support the tunnel service.

Get HP 6125G PDF manuals and user guides View all HP 6125G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 152 highlights

[SwitchA] ipv6 # Configure an IPv4 address for VLAN-interface 100. [SwitchA] interface vlan-interface 100 [SwitchA-Vlan-interface100] ip address 30.1.1.1 255.255.255.0 [SwitchA-Vlan-interface100] quit # Configure an IPv6 address for VLAN-interface 101 (the physical interface of the tunnel). [SwitchA] interface vlan-interface 101 [SwitchA-Vlan-interface101] ipv6 address 2002::1:1 64 [SwitchA-Vlan-interface101] quit # Create service loopback group 1 to support the tunnel service. [SwitchA] service-loopback group 1 type tunnel # Assign GigabitEthernet 1/0/3 to service loopback group 1, and disable STP, and LLDP. [SwitchA] interface GigabitEthernet 1/0/3 [SwitchA-GigabitEthernet1/0/3] undo stp enable [SwitchA-GigabitEthernet1/0/3] undo lldp enable [SwitchA-GigabitEthernet1/0/3] port service-loopback group 1 [SwitchA-GigabitEthernet1/0/3] quit # Create interface Tunnel 1. [SwitchA] interface tunnel 1 # Configure an IPv4 address for interface Tunnel 1. [SwitchA-Tunnel1] ip address 30.1.2.1 255.255.255.0 # Configure the tunnel encapsulation mode. [SwitchA-Tunnel1] tunnel-protocol ipv4-ipv6 # Configure the source address for interface Tunnel 1 (IP address of VLAN-interface 101). [SwitchA-Tunnel1] source 2002::1:1 # Configure the destination address of interface Tunnel 1 (IP address of VLAN-interface 101 of Switch B). [SwitchA-Tunnel1] destination 2002::2:1 # Reference service loopback group 1 on the tunnel. [SwitchA-Tunnel1] service-loopback-group 1 [SwitchA-Tunnel1] quit # Configure a static route from Switch A through interface Tunnel 1 to Group 2. [SwitchA] ip route-static 30.1.3.0 255.255.255.0 tunnel 1 • Configure Switch B: # Enable IPv6. system-view [SwitchB] ipv6 # Configure an IPv4 address for VLAN-interface 100. [SwitchB] interface vlan-interface 100 [SwitchB-Vlan-interface100] ip address 30.1.3.1 255.255.255.0 [SwitchB-Vlan-interface100] quit # Configure an IPv6 address for VLAN-interface 101 (the physical interface of the tunnel). [SwitchB] interface vlan-interface 101 [SwitchB-Vlan-interface101] ipv6 address 2002::2:1 64 [SwitchB-Vlan-interface101] quit 144

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
144
[SwitchA] ipv6
# Configure an IPv4 address for VLAN-interface 100.
[SwitchA] interface vlan-interface 100
[SwitchA-Vlan-interface100] ip address 30.1.1.1 255.255.255.0
[SwitchA-Vlan-interface100] quit
# Configure an IPv6 address for VLAN-interface 101 (the physical interface of the tunnel).
[SwitchA] interface vlan-interface 101
[SwitchA-Vlan-interface101] ipv6 address 2002::1:1 64
[SwitchA-Vlan-interface101] quit
# Create service loopback group 1 to support the tunnel service.
[SwitchA] service-loopback group 1 type tunnel
# Assign GigabitEthernet 1/0/3 to service loopback group 1, and disable STP, and LLDP.
[SwitchA] interface GigabitEthernet 1/0/3
[SwitchA-GigabitEthernet1/0/3] undo stp enable
[SwitchA-GigabitEthernet1/0/3] undo lldp enable
[SwitchA-GigabitEthernet1/0/3] port service-loopback group 1
[SwitchA-GigabitEthernet1/0/3] quit
# Create interface Tunnel 1.
[SwitchA] interface tunnel 1
# Configure an IPv4 address for interface Tunnel 1.
[SwitchA-Tunnel1] ip address 30.1.2.1 255.255.255.0
# Configure the tunnel encapsulation mode.
[SwitchA-Tunnel1] tunnel-protocol ipv4-ipv6
# Configure the source address for interface Tunnel 1 (IP address of VLAN-interface 101).
[SwitchA-Tunnel1] source 2002::1:1
# Configure the destination address of interface Tunnel 1 (IP address of VLAN-interface 101 of
Switch B).
[SwitchA-Tunnel1] destination 2002::2:1
# Reference service loopback group 1 on the tunnel.
[SwitchA-Tunnel1] service-loopback-group 1
[SwitchA-Tunnel1] quit
# Configure a static route from Switch A through interface Tunnel 1 to Group 2.
[SwitchA] ip route-static 30.1.3.0 255.255.255.0 tunnel 1
•
Configure Switch B:
# Enable IPv6.
<SwitchB> system-view
[SwitchB] ipv6
# Configure an IPv4 address for VLAN-interface 100.
[SwitchB] interface vlan-interface 100
[SwitchB-Vlan-interface100] ip address 30.1.3.1 255.255.255.0
[SwitchB-Vlan-interface100] quit
# Configure an IPv6 address for VLAN-interface 101 (the physical interface of the tunnel).
[SwitchB] interface vlan-interface 101
[SwitchB-Vlan-interface101] ipv6 address 2002::2:1 64
[SwitchB-Vlan-interface101] quit