Home » HP Manuals » Desktops » HP Dc7700 » Manual Viewer

HP Dc7700 HP Compaq dx7300 and dc7700 Business PC Technical Reference Guide, 1 - Page 146

F9=Boot Menu, Storage &gt, Boot Order, F10=Setup, F12=Network Service Boot, Table 8-2, Setup Utility

UPC - 882780715318

Add to My Manuals
Save this manual to your list of manuals

Page 146 highlights

BIOS ROM Table 8-2 Setup Utility Heading Option Description Advanced* *For advanced users only Power-On Options Allows you to set: • POST mode (QuickBoot, FullBoot, or FullBoot every 1-30 days). • POST messages (enable/disable). • F9 prompt (enable/disable). Enabling this feature will display the text F9=Boot Menu during POST. Disabling this feature prevents the text from being displayed but pressing F9 will still access the Shortcut Boot (Order) Menu screen. See Storage > Boot Order for more information. • F10 prompt (enable/disable). Enabling this feature will display the text F10=Setup during POST. Disabling this feature prevents the text from being displayed but pressing F10 will still access the Setup screen. • F12 prompt (enable/disable). Enabling this feature will display the text F12=Network Service Boot during POST. Disabling this feature prevents the text from being displayed but pressing F12 will still force the system to attempt booting from the network. • Option ROM* prompt (enable/disable). Enabling this feature will cause the system to display a message before loading options ROMs. (This feature is supported on select models only.) • Remote wakeup boot source (remote server/local hard drive). • After Power Loss (off/on/previous state): After power loss, if you connect your computer to an electric power strip and would like to turn on power to the computer using the switch on the power strip, set this option to ON. ✎ If you turn off power to your computer using the switch on a power strip, you will not be able to use the suspend/sleep feature or the Remote Management features. • POST Delay (in seconds) (enable/disable). Enabling this feature will add a user-specified delay to the POST process. This delay is sometimes needed for hard disks on some PCI cards that spin up very slowly; so slowly that they are not ready to boot by the time POST is finished. The POST delay also gives you more time to press F10 to enter Computer (F10) Setup. • I/O APIC Mode (enable/disable). Enabling this feature will allow Microsoft Windows Operating Systems to run optimally. This feature must be disabled for certain non-Microsoft Operating Systems to work properly. ✎ Support for specific Computer Setup options may vary depending on the hardware configuration. 8-12 www.hp.com Technical Reference Guide

Section	Page
Title	1
Contents	3
Chap_1_Introduction_final_review.pdf	7
Introduction	7
1.1 About this Guide	7
1.1.1 Online Viewing	7
1.1.2 Hardcopy	7
1.2 Additional Information Sources	7
1.3 Model Numbering Convention	7
1.4 Serial Number	9
1.5 Notational Conventions	9
1.5.1 Values	9
1.5.2 Ranges	9
1.5.3 Register Notation and Usage	9
1.5.4 Bit Notation and Byte Values	9
1.6 Common Acronyms and Abbreviations	10
Chap_2_System_Overview_final.pdf	17
System Overview	17
2.1 Introduction	17
2.2 Features	18
2.3 Mechanical Design	20
2.3.1 Cabinet Layouts	21
2.3.2 Chassis Layouts	26
2.3.3 Board Layouts	30
2.4 System Architecture	33
2.4.1 Intel Processor Support	35
2.4.2 Chipset	36
2.4.3 Support Components	37
2.4.4 System Memory	37
2.4.5 Mass Storage	38
2.4.6 Serial and Parallel Interfaces	38
2.4.7 Universal Serial Bus Interface	38
2.4.8 Network Interface Controller	38
2.4.9 Graphics Subsystem	39
2.4.10 Audio Subsystem	39
2.5 Specifications	40
Chap_3_Processor_final_review.pdf	45
Processor/Memory Subsystem	45
3.1 Introduction	45
3.2 Intel Pentium Processors	46
3.2.1 Intel Processor Overview	46
3.2.2 Processor Upgrading	48
3.3 Memory Subsystem	48
Chap_4_System_Support_final_review.pdf	53
System Support	53
4.1 Introduction	53
4.2 PCI Bus Overview	53
4.2.1 PCI 2.3 Bus Operation	54
4.2.2 PCI Express Bus Operation	58
4.2.3 Option ROM Mapping	60
4.2.4 PCI Interrupts	60
4.2.5 PCI Power Management Support	60
4.2.6 PCI Connectors	61
4.3 System Resources	63
4.3.1 Interrupts	63
4.3.2 Direct Memory Access	68
4.4 Real-Time Clock and Configuration Memory	71
4.4.1 Clearing CMOS	71
4.4.2 Standard CMOS Locations	72
4.5 System Management	72
4.5.1 Security Functions	72
4.5.2 Power Management	74
4.5.3 System Status	75
4.5.4 Thermal Sensing and Cooling	75
4.6 Register Map and Miscellaneous Functions	76
4.6.1 System I/O Map	76
4.6.2 SCH5317 I/O Controller Functions	77
Chap_5_Input-Output_Interfaces_final_review.pdf	79
Input/Output Interfaces	79
5.1 Introduction	79
5.2 SATA Interfaces	79
5.2.1 SATA Programming	79
5.2.2 SATA Connector	81
5.2.3 RAID Functionality	81
5.3 Diskette Drive Interface	82
5.3.1 Diskette Drive Programming	82
5.3.2 Diskette Drive Connector	86
5.4 Serial Interface	87
5.4.1 Serial Connector	87
5.4.2 Serial Interface Programming	87
5.5 Parallel Interface	89
5.5.1 Standard Parallel Port Mode	89
5.5.2 Enhanced Parallel Port Mode	89
5.5.3 Extended Capabilities Port Mode	90
5.5.4 Parallel Interface Programming	90
5.5.5 Parallel Interface Connector	92
5.6 Keyboard/Pointing Device Interface	93
5.6.1 Keyboard Interface Operation	93
5.6.2 Pointing Device Interface Operation	95
5.6.3 Keyboard/Pointing Device Interface Programming	95
5.6.4 Keyboard/Pointing Device Interface Connector	99
5.7 Universal Serial Bus Interface	100
5.7.1 USB Data Formats	101
5.7.2 USB Programming	102
5.7.3 USB Connector	103
5.7.4 USB Cable Data	104
5.8 Audio Subsystem	105
5.8.1 HD Audio Controller	106
5.8.2 HD Audio Interface	106
5.8.3 HD Audio Codec	107
5.8.4 Audio Programming	108
5.8.5 Audio Specifications	110
5.9 Network Interface Controller	111
5.9.1 Wake-On-LAN Support	112
5.9.2 Alert Standard Format Support	112
5.9.3 Power Management Support	112
5.9.4 NIC Programming	113
5.9.5 NIC Connector	113
5.9.6 NIC Specifications	114
Chap_6_Integrated_Graphics_final_review.pdf	115
Integrated Graphics Subsystem	115
6.1 Introduction	115
6.2 Functional Description	116
6.3 Display Modes	118
6.4 Upgrading Graphics	119
6.5 VGA Monitor Connector	120
Chap_7_Power_and_Signal_final_review.pdf	121
Power and Signal Distribution	121
7.1 Introduction	121
7.2 Power Supply Assembly/Control	121
7.2.1 Power Supply Assembly	122
7.2.2 Power Control	124
7.2.3 Power Management	127
7.3 Power Distribution	128
7.4 Signal Distribution	131
Chap_8_BIOS_ROM_final_review.pdf	135
BIOS ROM	135
8.1 Introduction	135
8.2 ROM Flashing	136
8.2.1 Upgrading	136
8.2.2 Changeable Splash Screen	137
8.3 Boot Functions	137
8.3.1 Boot Device Order	137
8.3.2 Network Boot (F12) Support	138
8.3.3 Memory Detection and Configuration	138
8.3.4 Boot Error Codes	139
8.4 Setup Utility	140
8.5 Client Management Functions	149
8.5.1 System ID and ROM Type	150
8.5.2 Temperature Status	150
8.5.3 Drive Fault Prediction	150
8.6 SMBIOS	151
8.7 USB Legacy Support	151
App_A_Error_Messages__amp__Codes_final_review.pdf	153
A.1 Introduction	153
A.2 Beep/Power LED Codes	153
A.3 Power-On Self Test (POST) Messages	154
A.4 System Error Messages (1xx-xx)	157
A.5 Memory Error Messages (2xx-xx)	158
A.6 Keyboard Error Messages (30x-xx)	159
A.7 Printer Error Messages (4xx-xx)	160
A.8 Video (Graphics) Error Messages (5xx-xx)	160
A.9 Diskette Drive Error Messages (6xx-xx)	161
A.10 Serial Interface Error Messages (11xx-xx)	162
A.11 Modem Communications Error Messages (12xx-xx)	163
A.12 System Status Error Messages (16xx-xx)	164
A.13 Hard Drive Error Messages (17xx-xx)	165
A.14 Hard Drive Error Messages (19xx-xx)	167
A.15 Video (Graphics) Error Messages (24xx-xx)	168
A.16 Audio Error Messages (3206-xx)	168
A.17 DVD/CD-ROM Error Messages (33xx-xx)	169
A.18 Network Interface Error Messages (60xx-xx)	169
A.19 SCSI Interface Error Messages (65xx-xx, 66xx-xx, 67xx-xx)	170
A.20 Pointing Device Interface Error Messages (8601-xx)	171
App_B_ASCII_Character_Set_final_review.pdf	173
B.1 Introduction	173
App_C_Keyboard_final_review.pdf	177
C.1 Introduction	177
C.2 Keystroke Processing	177
C.2.1 PS/2-Type Keyboard Transmissions	179
C.2.2 USB-Type Keyboard Transmissions	180
C.2.3 Keyboard Layouts	180
C.2.4 Keys	183
C.2.5 Keyboard Commands	186
C.2.6 Scan Codes	187
C.3 Connectors	193

Match case Limit results 1 per page

8-12

www.hp.com

Technical Reference Guide

BIOS ROM

Advanced*

*For

advanced

users only

Power-On Options

Allows you to set:

• POST mode (QuickBoot, FullBoot, or FullBoot every 1-30 days).

• POST messages (enable/disable).

•

prompt (enable/disable). Enabling this feature will display

the text

F9=Boot Menu

during POST. Disabling this feature

prevents the text from being displayed but pressing

will still

access the Shortcut Boot (Order) Menu screen. See

Storage >

Boot Order

for more information.

•

F10

prompt (enable/disable). Enabling this feature will display

the text

F10=Setup

during POST. Disabling this feature

prevents the text from being displayed but pressing

F10

will still

access the Setup screen.

•

F12

prompt (enable/disable). Enabling this feature will display

the text

F12=Network Service Boot

during POST.

Disabling this feature prevents the text from being displayed but

pressing

F12

will still force the system to attempt booting from

the network.

• Option ROM* prompt (enable/disable). Enabling this feature

will cause the system to display a message before loading

options ROMs. (This feature is supported on select models only.)

• Remote wakeup boot source (remote server/local hard drive).

•

After Power Loss (off/on/previous state): After power loss, if you

connect your computer to an electric power strip and would like

to turn on power to the computer using the switch on the power

strip, set this option to

✎

If you turn off power to your computer using the switch on a

power strip, you will not be able to use the suspend/sleep feature

or the Remote Management features.

•

POST Delay (in seconds) (enable/disable). Enabling this feature

will add a user-specified delay to the POST process. This delay

is sometimes needed for hard disks on some PCI cards that spin

up very slowly; so slowly that they are not ready to boot by the

time POST is finished. The POST delay also gives you more time

to press

F10

to enter Computer (F10) Setup.

• I/O APIC Mode (enable/disable). Enabling this feature will

allow Microsoft Windows Operating Systems to run optimally.

This feature must be disabled for certain non-Microsoft

Operating Systems to work properly.

Table 8-2

Setup Utility

Heading

Option

Description

✎

Support for specific Computer Setup options may vary depending on the hardware configuration.