Home » HP Manuals » Multifunction Devices » HP LaserJet 3200 » Manual Viewer

HP LaserJet 3200 Service Manual - Page 43

Printer Door Open Or, Is Empty. Add Paper - paper jam

Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Table 7. Control panel error messages (continued) Message POWER FAIL RECOVERY. CHECKING SYSTEM POWER FAIL RECOVERY. FAX SETTING RESET POWER FAIL RECOVERY. PRINTING FAXES POWER FAIL RECOVERY. SEND:[FAX NUMBER] POWER OFF. CHECK DIMM #[1-3] PRINTER PAPER JAM CLEAR PAPER PATH PRINTER DOOR OPEN OR NO TONER CARTRIDGE PRINTER PAPER TRAY IS EMPTY. ADD PAPER PRINTER TRAY MISPICK. [ENTER] TO RESUME Cause Solution The product has detected a power failure and is performing a self-test. The product has detected a power failure and the last update to the fax settings was corrupted. The product is resetting all fax settings to the factory default settings. The product has detected a power failure and is printing all of the faxes that it did not previously print. The product has detected a power failure and has also detected unsent faxes and will try to resend them. The DIMM in the indicated slot has failed. The product should go back to the ready state on its own. If this message does not go away in a couple of minutes, disconnect the power cable from the product, wait at least 30 seconds, then reconnect the power cable and wait for the product to initialize. Press STOP/CLEAR to clear the error. The product should return to the ready state. The product prints all of the received faxes that it did not previously print. Once the faxes are printed, the product will return to the ready state. The product resents the unsent faxes. Once the faxes are sent, the product will return to the ready state. Turn off the product and check the indicated DIMM. The product has detected that a jam has occurred. The printer door is open or the toner cartridge is not installed properly. The paper input tray is empty. The print engine has failed to pick up a piece of media. Clear the jam. The job should continue to print. If it does not, try reprinting the job. Make sure the printer door is closed. Check the toner cartridge for proper installation. Load media. If media is already loaded, remove it. Check for and remove any jam, and then reload the stack of media in the paper input tray. Reload the paper in the paper input tray and press ENTER/ MENU to continue the job. EN Control panel error messages 41

Section	Page
Contents	5
Figures	9
Tables	13
Product information	15
Chapter contents	15
Introduction	16
Hardware description	16
Firmware description	17
Product specifications	18
Model and serial numbers	21
Product overview	22
Warranty statement	25
Hewlett-Packard limited warranty statement	25
Declaration of Conformity	27
Toner cartridge information	28
Additional product stewardship	29
Environmental conformity	29
Installation and operation	31
Chapter contents	31
Operating environment	32
Identifying product components	33
Control panel lights and keys	33
Using the control panel menu structure	35
Control panel error messages	37
Selecting media	45
Selecting media to print	45
Selecting media to fax, copy, or scan	46
Loading media	47
Loading media to fax, copy, or scan	47
Loading media to be printed	50
Selecting the output path	52
Maintenance	53
Chapter contents	53
Life expectancies of consumables	54
Cleaning and maintaining the equipment	55
Cleaning the product	56
Cleaning the scanner path	59
Recalibrating the scanner	61
User-replaceable parts	62
Operational overview	63
Chapter contents	63
Basic functions	64
Optical system	65
Formatter system	67
Control panel	68
Draft mode	68
MEt	68
Enhanced I/O	68
Page Protect	69
PJL Overview	69
Printer functions	70
Engine control unit/power system	71
Image formation system	76
Printer paper feed system	79
Basic sequence of operation (formatter-to-printer)	84
Removal and replacement	87
Chapter contents	87
Removal and replacement strategy	89
Required tools	89
Parts removal order	90
Covers	91
DIMMs	91
Back cover	92
Right side cover	93
Left side cover	95
Internal paper guide	96
Top cover	97
Document scanner assemblies	98
Printer door	98
Document scanner assembly	102
Contact image sensor	105
Document scanner pickup roller	107
Document scanner separation pad	108
Document scanner motor	109
Upper guide assembly	110
Control panel/scanner board	114
Internal assemblies	115
Laser/scanner assembly	115
Output roller	116
Delivery assembly	118
Paper exit-sensor flag	120
Fusing element	121
Gear train motor	126
Solenoid	129
Pressure roller	130
Transfer roller	132
Pickup roller	133
Paper-pickup assembly	134
Kick plate	136
Separation pad	137
Bottom assemblies	139
Formatter pan	139
Formatter and LIU	140
ECU pan	141
Paper-feed assembly	143
Troubleshooting	147
Chapter contents	147
Basic troubleshooting	148
Errors	151
Image formation troubleshooting	157
Checking the toner cartridge	157
Solving image-quality problems	158
Solving paper feed problems	164
Functional checks	167
Engine test	167
Half-self-test functional check	168
Drum rotation functional check	169
Heating element check	170
High-voltage power supply check	171
Paper path check	173
Service mode functions	174
Secondary service menu	174
Developer’s menu	175
Diagnostic mode	183
NVRAM init	185
PJL software commands	185
Troubleshooting tools	188
Internal reports	188
Printing all fax reports at once	189
T.30 protocol trace	190
Repetitive image defect ruler	209
Document scanner recalibration	210
Main wiring	212
Locations of connectors	214
Parts and diagrams	217
Chapter contents	217
Ordering parts and supplies	218
Parts	218
Parts exchange program	219
Related documentation and software	219
Consumables	219
Accessories	220
How to use the parts lists and diagrams	221
Common hardware	222
Assembly locations	223
Covers	224
Trays and bins	225
External covers and panels	227
Document scanner assemblies	228
Document scanner assemblies	229
Document feeder	231
Upper guide assembly	233
Internal assemblies	234
Internal components (1 of 4)	235
Internal components (2 of 4)	237
Internal components (3 of 4)	239
Internal components (4 of 4)	241
Feed assembly	243
Electrical components	245
Alphabetical parts list	246
Numerical parts list	251
Index	257
A	257
B	257
C	257
D	258
E	258
F	259
G	259
H	260
I	260
J	260
K	260
L	260
M	261
N	261
O	261
P	261
Q	263
R	263
S	263
T	264
U	265
V	265

Match case Limit results 1 per page

Control panel error messages

POWER FAIL RECOVERY.

CHECKING SYSTEM

The product has detected a

power failure and is performing a

self-test.

The product should go back to

the ready state on its own. If this

message does not go away in a

couple of minutes, disconnect the

power cable from the product,

wait at least 30 seconds, then

reconnect the power cable and

wait for the product to initialize.

POWER FAIL RECOVERY.

FAX SETTING RESET

The product has detected a

power failure and the last update

to the fax settings was corrupted.

The product is resetting all fax

settings to the factory default

settings.

Press

TOP

LEAR

to clear the

error. The product should return

to the ready state.

POWER FAIL RECOVERY.

PRINTING FAXES

The product has detected a

power failure and is printing all of

the faxes that it did not previously

print.

The product prints all of the

received faxes that it did not

previously print. Once the faxes

are printed, the product will return

to the ready state.

POWER FAIL RECOVERY.

SEND:[FAX NUMBER]

The product has detected a

power failure and has also

detected unsent faxes and will try

to resend them.

The product resents the unsent

faxes. Once the faxes are sent,

the product will return to the

ready state.

POWER OFF.

CHECK DIMM #[1-3]

The DIMM in the indicated slot

has failed.

Turn off the product and check

the indicated DIMM.

PRINTER PAPER JAM

CLEAR PAPER PATH

The product has detected that a

jam has occurred.

Clear the jam. The job should

continue to print. If it does not, try

reprinting the job.

PRINTER DOOR OPEN OR

NO TONER CARTRIDGE

The printer door is open or the

toner cartridge is not installed

properly.

Make sure the printer door is

closed. Check the toner cartridge

for proper installation.

PRINTER PAPER TRAY

IS EMPTY. ADD PAPER

The paper input tray is empty.

Load media. If media is already

loaded, remove it. Check for and

remove any jam, and then reload

the stack of media in the paper

input tray.

PRINTER TRAY MISPICK.

[ENTER] TO RESUME

The print engine has failed to

pick up a piece of media.

Reload the paper in the paper

input tray and press

NTER

ENU

to continue the job.

Table 7.

Control panel error messages (continued)

Message

Cause

Solution