Panasonic WJSX650 WJSX650 User Guide - Page 37
System Status Check, Wv-cu950/650, Wv-cu360c/cj - pdf
View all Panasonic WJSX650 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 37 highlights
Terminal Alarm Output 1 to 32 Duration Until reset Alarm Recover Input 1 to 16 100 or more ms Time Adjust Output 1 second Time Adjust Input 100 or more ms Remarks Open Collector output, 24 V, 100 mA maximum Non-voltage make contact output • Open Collector output, 24 V, 100 mA maximum • Signal is output every hour on the hour. • Non-voltage make contact input • Signal input is accepted by up to ± 30 seconds every hour on the hour. Time is adjusted on the hour. Note: "Alarm Recover Input 1 to 16" can be used as "Alarm Monitor Reset". (Refer to p. 68.) I System Status Check During connection procedures, system status can be checked on 4 monitors. The following examples are procedures to display the system status on Monitor 1 to 4. G WV-CU950/650 1. Select one of Monitor 1 to 4. (Refer to p. 57 Monitor Selection.) 2. Press the MENU button repeatedly until "System Status" appears on the LCD. 3. Press the F1 button. SYSTEM STATUS will be displayed on Monitor 1 to 4. Note: SYSTEM STATUS is displayed on a set of 4 monitors (Monitor 5 to 8, Monitor 9 to 12...Monitor 29 to 32). G WV-CU360C/CJ 1. Select one of Monitor 1 to 4. (Refer to p. 57 Monitor Selection.) 2. Press the OSD and SYS S buttons at a time. SYSTEM STATUS will be displayed on Monitor 1 to 4. Note: SYSTEM STATUS is displayed on a set of 4 monitors (Monitor 5 to 8, Monitor 9 to 12...Monitor 29 to 32). Display example of SYSTEM STATUS LCN, MODE, KB and OPE parameters are highlighted for monitors during the alarm mode status. SYSTEM STATUS MON LCN MODE KB OPE PRI 01 001 02 002 03 200 04 030 05 100 G08 06 SETUP 07 HISTORY 08 R16 K1-1 123 01 03 /T001 99 PC 999 14 K1-4 5 00 K3-2 10 02 505 03 LCN:LOGICAL CAMERA NUMBER LCN and MODE parameters are highlighted for monitors during the alarm ACK status. SYSTEM STATUS MON LCN MODE KB OPE PRI 25 26 075 27 105 T32 28 002 T01 29 301 G32 30 401 G32 31 501 G32 32 999 PSD 48 02 /T128 60 K6-3 3 05 12345 10 12345 10 K8-4 12345 10 LCN:LOGICAL CAMERA NUMBER MON: Monitor number LCN: Camera number or recorder number MODE: Display mode of the monitor • SETUP: System Setup • HISTORY: Alarm History Display KB: System controller or PC OPE: User ID of the operator or timer event No. PRI: Operator priority • When SETUP MENU is displayed, "0" appears on this area. • During monitor lock, this area is highlighted. Notes: • Even while SYSTEM STATUS is being displayed on monitors, normal operations and alarm control are available. However, you cannot check the camera or recorded images because black screen is displayed. It is recommended to use these monitors only to check SYSTEM STATUS. • Up to 100 records of SYSTEM STATUS are saved in the system. These records can be transmitted between PC and this unit. (Periodical transmission is also available.) For transmission, perform the serial command settings in "Communication" - "Serial Command" of WJ-SX650 Series Administrator Console. • To transmit SYSTEM STATUS records from the PC, refer to Serial (RS-232C) Connector Command Reference (PDF file on the supplied CD-ROM). 37