Sharp AR-M237 AR-M237 AR-M277 Operation Manual Suite - Page 137

Place the next set of original s, and press the [START] key, When the last original has been

Get Sharp AR-M237 - B/W Laser - Copier PDF manuals and user guides View all Sharp AR-M237 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 137 highlights

BASIC OPERATIONS 8 Place the next set of original pages and press the [START] key ( ). Repeat this step until all pages have been scanned. You can change the original size, resolution, and exposure settings as needed for each page. If you take no action for about 1 minute (you do not press the [START] key ( )), scanning automatically ends and the job is stored for transmission. 9 When the last original page has been scanned, touch the [READ-END] key. (Pg.No. 2) L. A beep sounds to inform you that the job has been stored for transmission. ESS [READ-END] READ-END [JOB STORED.] appears in the message display. (Dialing and transmission begin automatically when any previously stored jobs are completed.) Note If you do not touch the [READ-END] key to complete the procedure, the screen will automatically revert to the initial screen after 60 seconds. If desired, you can disable automatic return to the initial screen by changing a setting in the key operator programs. (See "DISABLE DISPLAY TIMEOUT" in the key operator's guide.) When the screen reverts to the initial screen, the scanned originals will be transmitted. 2 Note • If the memory becomes full while originals are being scanned, a message will appear and scanning will stop. The page that was being scanned when the memory became full will be cleared. To transmit only the originals that have already been scanned, touch the [SEND] key. To cancel the transmission, touch the [CANCEL] key. • Depending on the content of the originals, the memory may become full before 100 pages are scanned. • When using job build mode, the number of originals scanned will appear in the display. When the count reaches 256 pages, it will reset to 0 and further scanned pages will be counted from 1. • When using job build mode, the original size can be changed between originals. • When scanning the first set of originals, the [ROTATE THE IMAGE 90 DEGREES] checkbox can be selected, however, from the second set of originals on, the selection cannot be changed until scanning is finished (the checkbox will be grayed out). • Direct transmission is not possible when using job build mode. A job build transmission takes place as a memory transmission even if Quick Online is enabled (transmission does not begin until all originals are scanned). 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
19
BASIC OPERATIONS
2
8
Place the next set of original pages
and press the [START] key (
).
Repeat this step until all pages have been scanned.
You can change the original size, resolution, and
exposure settings as needed for each page.
If you take no action for about 1 minute (you do not
press the [START] key (
)), scanning automatically
ends and the job is stored for transmission.
9
When the last original page has been
scanned, touch the [READ-END] key.
A beep sounds to inform
you that the job has been
stored for transmission.
[JOB STORED.] appears
in the message display.
(Dialing and transmission
begin automatically when
any previously stored
jobs are completed.)
If you do not touch the [READ-END] key to
complete the procedure, the screen will
automatically revert to the initial screen after
60 seconds. If desired, you can disable
automatic return to the initial screen by
changing a setting in the key operator
programs. (See "DISABLE DISPLAY
TIMEOUT" in the key operator's guide.)
When the screen reverts to the initial
screen, the scanned originals will be
transmitted.
READ-END
(Pg.No.
2)
L.
ESS [READ-END]
Note
•
If the memory becomes full while originals are being scanned, a message will appear and scanning will stop.
The page that was being scanned when the memory became full will be cleared. To transmit only the originals
that have already been scanned, touch the [SEND] key. To cancel the transmission, touch the [CANCEL] key.
•
Depending on the content of the originals, the memory may become full before 100 pages are scanned.
•
When using job build mode, the number of originals scanned will appear in the display. When the count
reaches 256 pages, it will reset to 0 and further scanned pages will be counted from 1.
•
When using job build mode, the original size can be changed between originals.
•
When scanning the first set of originals, the [ROTATE THE IMAGE 90 DEGREES] checkbox can be selected,
however, from the second set of originals on, the selection cannot be changed until scanning is finished (the
checkbox will be grayed out).
•
Direct transmission is not possible when using job build mode. A job build transmission takes place as a
memory transmission even if Quick Online is enabled (transmission does not begin until all originals are
scanned).
Note