Xerox 6180N DocuTech 61xx - Operator HandyBook - Page 11

Paper Path Areas - not printing to tray 1

Page 11 highlights

Paper Path Areas System Hardware The numbers in figure 4-6 identify the following paper path are as follows: • Areas 1 to 4 - The stock leaves a paper tray and is fed to the photoreceptor. • Areas 5 to 10 - The system prints an image on one side of the stock. If the job requires 2-sided printing, the system turns the page over and feeds it back to the photoreceptor. • Areas A to H - This is the interposer area. Paper travels through this area if paper is fed from trays 1, 4 or 5 and also to pass paper from area 10 (through F and H) to the finisher. • Areas 11 and 12 - If the prints are to be fed to the top tray, the system delivers the prints through the top tray slot. • Areas 13 to 16 - The prints enter the bindexer and are collated, if desired. • Areas 17 to 19 - The prints are stitched in area 17, or bound in area 18, if desired, and placed on the stacker in area 19. DT6180 HandyBook 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168

System Hardware
DT6180 HandyBook
11
Paper Path Areas
The numbers in figure 4-6 identify the following paper path are as follows:
Areas 1 to 4
- The stock leaves a paper tray and is fed to the photoreceptor.
Areas 5 to 10
- The system prints an image on one side of the stock. If the job requires
2-sided printing, the system turns the page over and feeds it back to the photoreceptor.
Areas A to H
- This is the interposer area. Paper travels through this area if paper is fed
from trays 1, 4 or 5 and also to pass paper from area 10 (through F and H) to the finisher.
Areas 11 and 12
- If the prints are to be fed to the top tray, the system delivers the prints
through the top tray slot.
Areas 13 to 16
- The prints enter the bindexer and are collated, if desired.
Areas 17 to 19
- The prints are stitched in area 17, or bound in area 18, if desired, and
placed on the stacker in area 19.