Xerox 6180N DocuTech 61xx - Operator HandyBook - Page 80

Clean the Fuser Q1010 and Prefuser Sensors Q1009

Get Xerox 6180N - Phaser Color Laser Printer PDF manuals and user guides
UPC - 095205425307
View all Xerox 6180N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

Solutions in Alphabetical Order 16. Look 76 mm (3 inches) directly above the sensor for orange and white wires. These wires are attached to the detector which faces straight down. 17. Brush a folded sheet of paper across the Sensor. 18. Close the Finisher Front Doors. If present, lower the bypass transport. Close the Finisher Top Cover. Clean the Fuser (Q1010) and Prefuser Sensors (Q1009) Clean both the Q1010 and Q1009 Sensor, beginning with the Q1010 Sensor. WARNING: The surrounding area of the machine around the sensors can be extremely hot! Cleaning the Q1010 Sensor: 1. Open the Processor Doors. The handle to open the doors is above Paper Tray 1. 2. Behind the left Processor Door, just to the left of Paper Tray 1, is a large green handle. Pull on the handle and pull out the Fuser Module. 3. Locate the CAUTION label on top of the Fuser Module. 4. Approximately 25 mm (1 inch) to the left of the label is a small U-shaped cutout in the aluminum frame and a tiny square mirror the size of your small fingernail. DT6180 HandyBook 80

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
Solutions in Alphabetical Order
DT6180 HandyBook
80
16. Look 76 mm (3 inches) directly above the sensor for orange and white wires. These wires are
attached to the detector which faces straight down.
17. Brush a folded sheet of paper across the Sensor.
18. Close the Finisher Front Doors. If present, lower the bypass transport. Close the Finisher Top
Cover.
Clean the Fuser (Q1010) and Prefuser Sensors (Q1009)
Clean both the Q1010 and Q1009 Sensor, beginning with the Q1010 Sensor.
WARNING: The surrounding area of the machine around the sensors can be extremely hot!
Cleaning the Q1010 Sensor:
1.
Open the Processor Doors. The handle to open the doors is above Paper Tray 1.
2.
Behind the left Processor Door, just to the left of Paper Tray 1, is a large green handle. Pull on the
handle and pull out the Fuser Module.
3.
Locate the CAUTION label on top of the Fuser Module.
4.
Approximately 25 mm (1 inch) to the left of the label is a small U-shaped cutout in the aluminum
frame and a tiny square mirror the size of your small fingernail.