Xerox 6180N DocuTech 61xx - Operator HandyBook - Page 29

Replacing Consumables - consumer

Get Xerox 6180N - Phaser Color Laser Printer PDF manuals and user guides
UPC - 095205425307
View all Xerox 6180N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Replacing Consumables 4. Replacing Consumables Add Fuser Agent NOTE: You should add Fuser Agent as soon as possible after the message is displayed. If Fuser Agent is not added the machine will stop running after approximately 5,000 prints and will not run until Fuser Agent is added. To add Fuser Agent: 1. Open the Processor Doors. 2. Place a drop cloth on the floor under the Fuser area to catch any Fuser Agent that may spill. WARNING: The Fuser area can reach temperatures of approximately 425 ° F / 218 ° C. Use extreme care to prevent burns when working in this area. 3. Grasp the green handle and lift up to open the Fuser Drawer. 4. Pull the Fuser Drawer all the way out of the machine until it stops. WARNING: Fuser Agent contains silicone which can cause irritation upon contact with the eye. Use latex gloves if you have them or make sure that you wash your hands with soap and water after you finish this procedure. 5. Pull the Fuser Agent reservoir out until it stops. 6. Remove the reservoir cap. DT6180 HandyBook 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
Replacing Consumables
DT6180 HandyBook
29
4.
Replacing Consumables
Add
Fuser Agent
NOTE:
You should add Fuser Agent as soon as possible after the message is displayed. If Fuser
Agent is not added the machine will stop running after approximately 5,000 prints and will not run
until Fuser Agent is added.
To add Fuser Agent:
1.
Open the Processor Doors.
2.
Place a drop cloth on the floor under the Fuser area to catch any Fuser Agent that may
spill.
WARNING: The Fuser area can reach temperatures of approximately 425 ° F / 218 °
C. Use extreme care to prevent burns when working in this area.
3.
Grasp the green handle and lift up to open the Fuser Drawer.
4.
Pull the Fuser Drawer all the way out of the machine until it stops.
WARNING: Fuser Agent contains silicone which can cause irritation upon contact
with the eye. Use latex gloves if you have them or make sure that you wash your
hands with soap and water after you finish this procedure.
5.
Pull the Fuser Agent reservoir out until it stops.
6.
Remove the reservoir cap.