Xerox 6180N DocuTech 61xx - Operator HandyBook - Page 16

Adding Paper to Tray 1 or 2

Get Xerox 6180N - Phaser Color Laser Printer PDF manuals and user guides
UPC - 095205425307
View all Xerox 6180N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Paper Trays & Loading Media Adding Paper to Tray 1 or 2 The following steps must be performed to add paper to tray 1 or 2. 1. Press the Tray unlock button on the front of the tray. Wait for the red "Please wait" light to go off. 2. When the green "Ready to open" light comes on, pull the tray out until it stops. 3. Press the green release tab. 4. Lift the metal handle on the feed belt and remove any paper under the belt. 5. Move the rear guide to the back of the tray. NOTE: To load the paper correctly, refer to the label located on the inside panel at the front of the paper tray. Remove any damaged sheets from the top of the stack. Do not load the paper above the red line. A jam could occur if too much paper is loaded in the tray. 6. Load the required paper into the paper tray. Load paper with the curl side facing down. Load Xerox paper with the package wrapper seam side facing up. NOTE: When loading drilled paper, be sure to fan the edge where the holes are located. 7. Position the stack against the front right corner of the tray, as shown below. This is indicated by the green arrow on the bottom of the tray. DT6180 HandyBook 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
Paper Trays & Loading Media
DT6180 HandyBook
16
Adding Paper to Tray 1 or 2
The following steps must be performed to add paper to tray 1 or 2.
1.
Press the Tray unlock button on the front of the tray. Wait for the red "Please wait" light to
go off.
2.
When the green "Ready to open" light comes on, pull the tray out until it stops.
3.
Press the green release tab.
4.
Lift the metal handle on the feed belt and remove any paper under the belt.
5.
Move the rear guide to the back of the tray.
NOTE: To load the paper correctly, refer to the label located
on the inside panel at the front of the paper tray. Remove any
damaged sheets from the top of the stack.
Do not load the paper above the red line. A jam could occur if too
much paper is loaded in the tray.
6.
Load the required paper into the paper tray. Load paper with the
curl
side facing down
.
Load Xerox paper with the package wrapper seam side facing up.
NOTE: When loading
drilled paper
, be sure
to fan the edge
where the holes are
located.
7.
Position the stack against the front right corner of the tray, as shown below. This is
indicated by the green arrow on the bottom of the tray.