Xerox 6180N DocuTech 61xx - Operator HandyBook - Page 112

Clear the Paper Jam in Areas 5 and 6

Get Xerox 6180N - Phaser Color Laser Printer PDF manuals and user guides
UPC - 095205425307
View all Xerox 6180N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 112 highlights

Solutions in Alphabetical Order Clear the Paper Jam in Areas 5 and 6 To clear area 5: 1. Open the Processor Doors using the handle above Paper Tray 1. 2. To the left of Paper Tray 2 is a green handle with an arrow on it. Rotate the handle to the right, and hold it in this position. 3. Remove all paper from the area to the left of Paper Tray 2. 4. Rotate the handle to the left. To clear area 6: 5. Pull out the Fuser Assembly. Grasp the square gray handle with a horizontal green stripe and rotate it out and up at the same time. The handle is located above and to the left of Paper Tray 1. WARNING: The Fuser is very hot! 6. Remove any paper in the Fuser area. Make sure to look at the bottom of the Fuser Assembly for any trapped sheets of paper. 7. Push the Fuser Assembly into the machine until it stops. 8. Close the Processor Doors. NOTE: If the Processor Doors do not close completely, the Fuser Assembly is not positioned correctly. Pull the Fuser Assembly out slightly and then push the Fuser Assembly back into the machine until it stops. Even if paper is not visible, go through the sequence to clear the paper jam. Carefully inspect the rollers for any debris or torn pieces of paper. When clearing misfeeds, make sure a full sheet of paper was cleared and there are no pieces of paper left in the machine. DT6180 HandyBook 112

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
Solutions in Alphabetical Order
DT6180 HandyBook
112
Clear the Paper Jam in Areas 5 and 6
To clear area 5:
1.
Open the Processor Doors using the handle above Paper Tray 1.
2.
To the left of Paper Tray 2 is a green handle with an arrow on it. Rotate the handle to the right, and
hold it in this position.
3.
Remove all paper from the area to the left of Paper Tray 2.
4.
Rotate the handle to the left.
To clear area 6:
5.
Pull out the Fuser Assembly. Grasp the square gray handle with a horizontal green stripe and
rotate it out and up at the same time. The handle is located above and to the left of Paper Tray 1.
WARNING: The Fuser is very hot!
6.
Remove any paper in the Fuser area. Make sure to look at the bottom of the Fuser Assembly for
any trapped sheets of paper.
7.
Push the Fuser Assembly into the machine until it stops.
8.
Close the Processor Doors.
NOTE:
If the Processor Doors do not close completely, the Fuser Assembly is not positioned correctly. Pull
the Fuser Assembly out slightly and then push the Fuser Assembly back into the machine until it stops. Even
if paper is not visible, go through the sequence to clear the paper jam. Carefully inspect the rollers for any
debris or torn pieces of paper. When clearing misfeeds, make sure a full sheet of paper was cleared and
there are no pieces of paper left in the machine.